20 Most Recent Zebra Z4M Printer - Page 8 Questions & Answers

http://www.zebra.com/id/zebra/na/en/index/drivers_downloads/firmware/results.html?productType=6
Sir, kindly go there and the list contains the downloads which is just newly released.
Thank you Sir. Have a nice day.

Your Logic bd needs to be replaced or repaired.

Rory
Midrange Repair and Parts

pls refix printer catridge.

make sure the printer is calibrated. It should feed 1 label only. If it does not default it to force a calibration. hold pause and feed while off then turn on, count to 6 and release the buttons. You also need to set label height and width in the printer driver. Both zebra designer and zebra universial. goto printers and faxes and right click on your printer driver chose properties, this opens up on the general tab.

Configuration changes for current job and Default Configuration changes
There are two places in the driver configuration to change print configuration. In Windows 98, ME, 2000 and XP, go to the "General" tab and click the "Printing Preferences..." button. This menu of configuration parameters are the settings that are in effect for the current print job. Any changes made here will only affect the current, or next, print job. These settings are initialized for each print job from the configuration defaults.
Go to the "Advanced" tab and click the "Printing Defaults..." button. The displayed configuration menu describes the default settings for the driver. These settings are used to set the initial "Printing Preferences..." for new print jobs. It is a convenient place to set parameters that seldom change in you environment. Commonly set default parameters include Printer firmware, Media Settings, Device Options, and Page Size.
On Windows NT, these menus are available when you right click on the printer name in the Printers folder. The pop-up menu contains selections for "Printer Settings" and "Default Settings" which take you to these screens in the driver.

try to set the printer to the factory default setting

Z: is the firmware.......... try to upload it to E:

Hello,

You have a bad Logic Bd and it needs to be replaced or repaired.

Rory Cardenas
Midrange Repair and Parts

Hello,

You have a Bad Logic bd and it needs to be replaced

Rory Cardenas
Midrange Repair and Parts

Somehow, the correct printer driver is not installed when setting up Zebra Designer for XML.

To fix it, clck on "Start->All Programs->Zebra Designer for XML->Add Printer".

A wizard opens, select "Next" and choose the printer you are designing labels for. Click on "Next".

Select "Update existing printer driver(s)". The driver gets updated and voilá!, now you can export your label desgins.

Hello,

The only fix is to replace the logic bd.

I have plenty of them in stock and can repair them if needed.

Please contact me for pricing.

Thanks

Rory Cardenas
Midrange Repair and Parts
3821 W. 127th Place
Alsip IL 60803
708-597-4222 x240
[email protected]
AOL IM: RORYMRP

Hello,

It sounds to me like your Printhead is bad or is going bad. Have you tried cleaning your PH? If not you can try cleaning it with alcohol and a swab just be sure that the printer is off and unplugged and don’t touch the face of the Printhead with your fingers. If you have rubber gloves or surgical gloves please use them.

If this doesn’t help then you will need to replace. I carry brand new print heads in stock and offer a limited 30/day warranty for them. The normally run about 4 to 5 thundered dollars but I can supply my print heads at a fraction of the cost.

Please contact me if you have any questions.

Thanks

Rory Cardenas
Midrange Repair and Parts
Alsip IL 60803
708-597-4222 x240
[email protected]
AOL IM: RORYMRP

Hello,

You have a bad Main Logic Board and it needs to be replaced or fixed. I can supply refurbished Logic Boards at a good price outright or exchange. I can also repair your logic board at about half the price you would pay for a refurbished one. I also carry a 30/day warranty for a purchase and a 90/day warranty for a repair.

Please let me know if you have any other question.

Thank you.

Rory Cardenas
Midrange Repair and Parts
Alsip IL 60803
708-597-4222 X240
AOL IM: RORYMRP

Did you switch your ribbon as well?

Make sure printer is set for "non-continuous" supplies(media).
Also try calibrating printer. You can download a quick reference manual at zebra.com

Hello,

Have you tried sending print jobs thru the parallel port only? I think it has to deal with your jetdirect box. You can try reseting that as well.

Rory Cardenas
Midrange Repair and Parts
Alsip IL 60803
708-597-4222 x240
[email protected]
AOL IM: RORYMRP

did you try to find info at manufacrturers website or email them?

Hello,

It seems like your logic bd has gone bad. You will need to replace it with a new one.

I have that logic bd in stock and can offer to do it on exchange for your old one. Or if you like you can have the bad one repaired. We repair the logic bds here at my company.

Please contact me with any questions.

Rory Cardenas
Midrange Repair and Parts
Alsip IL 60803
708-597-4222 X240
[email protected]
AOL IM RORYMRP

This could be something simple like not having rewind (peel) selected in the setup menu. Or you could have a bad rewind motor or main logic board. Remove the cover and make sure no plugs have come loose. There isn't an easy way to check the motor or logic board unless you have a spare that you can swap.