Top 20 TP-LINK TL-WR1043ND Router Questions & Answers

You need to reset it to factory default by pressing the reset button for around 5 seconds. Once it is reset, the username and password is admin/admin. Or if you are a careful guy, you have backup your configuration in your PC, there is a software to read the configuration and extract the password for you. Good luck

Not in this model of the router, you can disable a particular mac address.

Best and easy thing u can do is to minimize the range of IP-s for example u have connected 25 pc-s by LAN just make the IP range for example from 192.168.0.50 to 192.168.0.75 plus minus 1 or more for wifi clients

block facebook on an iPod, try iKeyMonitor.http://ikeymonitor.comBlock websites on PC, try aobo filter for PChttp://www.parental-controls-software.net/

You can install a wireless range extender. Try a Netgear Dual Band WiFi Range Extender, this device extends the wireless range of your existing wireless router, it connects to your wireless router using a wireless connection without the need of a LAN cable.

First check the all connection,your LAN connector .Then Go to My Network Places and right click and select properties. Highlight your connection and look in the lower left at the Details information. Does the address look appropriate for your network, and does it say Assigned by DHCP or something else.otherwise you should contact internet provider..**If you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/

Find the DHCP settings From DHCP menuTurn off the DHCP server (which you have)Save your settingsIf you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/

yeap it should be the firewall, here is the manual http://www.tp-link.com/resources/software/201161017075118.pdf think this should help you.But if you want my expertise, make the tp-link as a router and vdsl just the internet line. connect it to router wan and buy a switch for all your devices.That should be the safest and smartest way.

You can also configure it with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Hello, in order to setup your TP-LINK extender just follow the full steps or guide from this video : https://www.youtube.com/watch?v=MpULi2wBjz4 I hope that helps you.

whats the exact issue?

Multiple users will slow each user down. Think of people filling glasses from the same water faucet. The faucet can only put out so much water. More users...less water per user. Same for router data flow. In your case, it could be too many users in your office or many users on the main feed line coming into your building Check with your internet provider. They can send a tech to measure data speed and identify what is causing your issues.

A repeater essentially I'd an extender

Hi Bob- I found this link. https://images-eu.ssl-images-amazon.com/images/I/C1BY5pXTUbS.pdf Hope this helps.

Hello, indicate model of the TP-Link that you are commenting, in order to find the best possible solution I wait your answer Greetings Franco Dosil Hola, indica modelo del TP-Link que estas comentando, para poder encontrar la mejor soluci?n posible Espero tu respuesta Saludos Franco Dosil

The laptop may not support 5ghz. Go to Device Manager and get the wireless network adapter name, so you can check online to verify if it supports 5ghz... R click win logo bottom left of desktop. L click device manager. Find and expand Network adapters.

pull out the power plug at back for 30 seconds . or at power point

Switches don't need any configuration whatsoever. So this should work without any trouble.

Re Install Drivers