Acer eMachines Black EL1352G-41w Desktop PC with AMD Athlon II X2 220 Processor and Windows 7 Home Premiu... (99802344405) - Answered Questions & Fixed issues

How to remove pop up

You will most likely find it at the bottom of your laptop that's where it usually is.

Emachines EL1352 01e EL1352 23e EL1352 43 EL1352G 41w Motherboard DA061L... if this is your board the battery if above the ram slot turned on side in holder right side of ram slot

Use the windows 7 reinstall disk that came with your computer...or return it to its owner and go buy yourself your own PC and stop stealing jk...

uninstall the ups software

you should let it finish,sometimes it takes a long time and many restarts by itself,lets be patient when restoring.

That password allows you to connect to your router or modem/router. The password may be printed on the router. If not, see this article:http://www.tomshardware.com/forum/36558-43-what-wpa2-password

No, When you plug in the Discrete graphics card it causes a bypass of the onboard video chip. The only system that will use the onboard video is the new APU units, and these only give a boost to the graphics card.

If you Have the DVD with Windows on it, Re install Windows.....

Sounds like an error on the Hard Drive

Have you tried your recovery disk or boot in safe mode?

eMachines are notorious for motherboards going out. What problems did you have to make you restore back to factory settings?

Yes, you can.

andrew it can be a microsoft update.which was pulled back some days ago.KB/2823324 i dont say it is,only it can be.

Contact Acer Support: http://support.gateway.com/us/en/emac/product/default.aspx?tab=1&modelId=3250

Hi,1) When did this start to happen?2) Try doing that twice? Or once and then press F5 to refresh.3) Contact Facebook by going to the help section - on the right top side.

Sometimes when you add media to your account you have to re-load the webpage before they show up? You might want to send the media to another program to make sure it opens correctly! I hope this helps. Let me know! If you need further help, reach me via phone at https://www.6ya.com/expert/greg_012fb269876eb4b0

Network security keySome later model wireless routers have the Password(ie.Encryption key) and the SSID already configured in the wireless router andthis information is printed on a label on the bottom of the router.These settings can be used to configure the wireless card and wireless adaptersin your computer/laptop. If these settings do not suit you, then it can be changed to suit yourrequirements. The encryption key secures your data and wireless connection from unauthorizedaccess.To configure the wireless settings in the router, connect a LAN cablefrom your computer to the wireless router, then open a Browser on your computerand enter the router's configuration IP address, then enter the admin login andpassword and then go to the wireless settings and configure the SSID andEncryption key.The router's encryption key can be a Passphrase or the WEP or WPA or WPA2key.If you use the Passphrase method select either WEP or WPA or WPA2 togenerate the encryption key. You can enter the WEP or WPA or WPA2 key with 8 to63 ASCII characters or 64 Hex digits.Most people use Passphrase which is easier to remember eg. I was born inJanuary 1988.The strongest and latest security is WPA2, the weakest and oldest is WEP. To connect to your wireless router from the computer/laptop,configure the wireless card in your computer/laptop with the router's wirelesssettings ie SSID, plus the WPA or WPA2 encryption key. Then computer/laptopscan communicate with your wireless router.http://www.fixya.com/support/r10267861-network_security_key

Here's the location of a utility that might help you:http://pcsupport.about.com/od/toolsofthetrade/gr/ophcrack.htm

Welcome to Fixya

Try this procedure: Go to your Computer Bios Setup (press Del when you turn on the compute).Go to "Power Management Setup" and enable " PWron/Resume by alarm" and set date alarm and time alarm and then press F10 to save your change and turn off your pc. Observed the pc if it will turn on.

If no PC will not respond then you might need to do a firmware upgrade otherwise you have a faulty motherboard.

Thank you for using FIyxa! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b