20 Most Recent Canon Pixma MX410 All-In-One Printer - Page 2 Questions & Answers

can mx410 send a confirmation after fax is sent

LF error - paper feeding problem

There are detailed instructions in the user manual at P007 You can download your manual here: http://www.canon.co.uk/support/consumer_products/products/fax__multifunctionals/inkjet/pixma_mx_series/pixma_mx410.aspx?type=manuals&language=

Ann, try plugging printer in and see if computer does a self installation. If not you may have to turn security off to install. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

I would start by cleaning under the print head. You could have some dust that's causing the blurring. You can also run a "cleaning cycle" and a "head alignment" which may help.

ELAINE, GET IN THE MANUEL LOOK UP SCAN, OR GOOGLE THAT MAKE & MODEL AND CALL CUSTOMER SUPPORT

I had the same problem, I own a Pixma MX410, first there is no need to turn off or unplug anything, simply go to your fax button then use the > < arrows to get to advanced fax from the menu button, then go to print reports; then smply print out the reports and then presto all of these reports come printing out and the blue Fax Memory light vanishes. What happened is that at some earlier point someone attempted to fax and it did not go through so it is store in the memory just waiting to be printed out. hope this helps you

Thank you, old marine! That fixed my problem!

the alignment is off. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/stephen_171aeeebef53a898

Line Feed error or Error Code 6000 Condition: An error occurred in the LF encoder signal. Problems and Solutions:

• Smearing or scratches on the LF / EJ slit film - clean the LF / EJ slit film.
• Foreign material or paper debris in the LF drive; - remove foreign material.
• If other solution fail, replace one off the following - LF / EJ slit film - LF / EJ timing sensor unit - Paper feed roller unit - Logic board - Paper feed motor

Try cleaning your rollers, it worked for me. I hope this helps.

I had the same problem. My DPI setting was at 25. I upped it to 600 and the document scanned perfectly.

Refilled cartridges give a lot of trouble , I only use genuine. click start, devices and printers , right click the printer image, click trouble shooter follow instructions. Don't be supprised if the only fix is a new cartridge.

Go to https://www.google.co.in/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0CCsQtwIwAg&url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DrGosAvJXSik&ei=FShcVbDvLNjkuQTK-YDoBQ&usg=AFQjCNE0rnyqBnwTMVj2XCF-vxqxnMPvcQ&sig2=PvFwB8SHcab_b9VC4QExbQ&bvm=bv.93756505,d.c2E or Canon Lion PIXMA MX410

if your running windows remove the usb cable it will make a noise in windows denk donk an plug it back it do you hear it again. now open the printer control panel an run a test

The question was for Mx410 but, below ya'll mention MX310. Is this solution for the MX 410 too.

Hi Laura, Most likely the jolt from falling to the floor must have knocked the ink cartridge carrier out of alignment or jammed it along the carrier rail...have the dog knock it over on its opposite side...no, no, no- just kidding!! Using a flashlight, can you see any obstructions, pieces of paper that may have jammed, or any broken pieces? I don't know how long you've had this printer for, but if you have to send it out for repair and it's going to cost more than 50% than buying a new one, don't repair it; you're throwing good money after bad...btw, dog proof the new one...ARF! Hope this helps :)

The sligtest burst in the plastic, or a rail out of place will stop the smooth movement of the print head. When you can't see an obvious error, like a tube out of place and you can't put it back, I'm affraid you should start saving for a new printer. The error should go away, as soon as the print head can move again (and correct) and you did power down the printer once. Don't blame the pinter, no printer will survive a fall. Don't blame the dog, he / she did not see it in time.

It sounds to me like you are having connectivity issues. Do you receive faxes over the phone line, wireless server or internet? Are there any other errors? If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_3e83613ef5f2a68b

Does it do anything? Did you try any of the suggestions below offered to others with auto feed problems? If none of those suggestions help you may want to reinstall your printer on your computer. Beyond that you may have to do single page scanning on the scanner.