20 Most Recent TP-LINK TL-MR3420 Wireless Router - Page 2 Questions & Answers

What is your OS?

Have you checked and reseated ALL the cables? Have you contacted your ISP to verify the signal? You can find a User manual : http://www.google.com/webhp?source=search_app#output=search&sclient=psy-ab&q=huawei+e173+manual&oq=Huawei+E173&gs_l=hp.1.1.0l4.2674.2674.0.4493.1.1.0.0.0.0.102.102.0j1.1.0...0.0...1c.2.11.psy-ab.fOKN7CfpHoM&pbx=1&bav=on.2,or.r_qf.&bvm=bv.45921128,d.eWU&fp=eee4d73fccc469f8&biw=1079&bih=577 The TP-LINK TL-MR3420 manual here: http://www.tp-link.com/en/products/details/?model=TL-MR3420

Push and hold the reset button for 30 seconds or so, release. A user manual can be found here: http://www.tp-link.com/us/products/details/?model=TL-MR3420#down

When you say US i take it you mean a united states IP adress and the simple answer is you cant. Ip adresses are issued by your isp. You can however use a proxy server that is based in the usa if you are trying to access a country specific site. Hope this helps.

Default IP adress to enter the configurationis http://192.168.1.1 user: adminpass: adminThen run the QUICK SETUP (installation wizard)For more details get the User guide

1.You will possibly need to configure the router for what is called "port Triggering"
2. from what I read is that there is no IP via the Hikvision external there fore requiring a new IP each time for connectivity.
Instruction set from the manual states:
To add a new rule, follow the steps below.
1. Click the Add New... button, the next screen will pop-up as shown in Figure 4-40.
2. Select a common application from the Common Applications drop-down list, then the
Trigger Port field and the Incoming Ports field will be automatically filled. If the Common
Applications do not have the application you need, enter the Trigger Port and the
Incoming Ports manually.
3. Select the protocol used for Trigger Port from the Trigger Protocol drop-down list, either
TCP, UDP, or All.
4. Select the protocol used for Incoming Ports from the Incoming Protocol drop-down list,
either TCP or UDP, or All.
5. Select Enable in Status field.
6. Click the Save button to save the new rule.
**************************************************************************
check the "Local management" in the router
you must allow certain devices to obtain an IP via either MAC address or IP address.

whats the exact issue?

have you got two dhcp servers running ? turn off dhcp server in wireless router and use the one in the Thomson TWG850-4 Residential Voice Gateway. make sure ip address in wireless router is different to the Thomson TWG850-4 Residential Voice Gateway. make it one higher on last digit of ip address make sure dhcp does not lease out this ip address.

Hello, in order to setup your TP-LINK extender just follow the full steps or guide from this video : https://www.youtube.com/watch?v=MpULi2wBjz4 I hope that helps you.

Multiple users will slow each user down. Think of people filling glasses from the same water faucet. The faucet can only put out so much water. More users...less water per user. Same for router data flow. In your case, it could be too many users in your office or many users on the main feed line coming into your building Check with your internet provider. They can send a tech to measure data speed and identify what is causing your issues.

Hi Bob- I found this link. https://images-eu.ssl-images-amazon.com/images/I/C1BY5pXTUbS.pdf Hope this helps.

A repeater essentially I'd an extender