20 Most Recent
Rolex Oyster Perpetual Datejust 116200BLSJ Watch for Men - Page 10 Questions & Answers
Pull out pin to set time, do I have to wind it up????
The only clue to what you have in front of you is that it might be a watch as you posted to the Watches category. All questions need 'make model (what it is)' as the first three words in every question.
Watches can be fully digital, with no crown (proper name for 'pull pin') to pull. They can be quartz electronic with an analogue dial and a crown. Finally they can be 'automatic', with no battery and powered by a spinning weight like my Rolex. that has a 3 way crown, pull to first position and it changes the date, pull all the way to change the time. My Seiko has a similar crown, but first position does the day when turned clockwise and the date when turned anti-clockwise. Pulling out all the way changes the hands.
Google
make model manual
..
6/24/2023 5:35:41 PM •
Watches
•
Answered
on Jun 24, 2023
How do I set the time on a Fanmis sport watch/pedometer
It's simple to change the time on a Fanmis sport pedometer. To get to the "Time" setting, all you have to do is keep pressing the "Mode" button. Then, after pressing the "Set" button, change the time using the "Start/Stop" and "Reset" buttons.
Once the time has been set, you may resume recording your steps and working toward your fitness objectives. After all, if you want to keep healthy, time is of the essence!
4/18/2023 8:29:08 PM •
Watches
•
Answered
on Apr 18, 2023
I need a crystal for a chaika watch
you cannot do this yourself ..try the manufacture or a competent repairer some crystals have to be made by hand if theres not one available through the trade repairers..
4/9/2023 7:28:19 PM •
Watches
•
Answered
on Apr 09, 2023
TVG watch manual
Ralph. This question is from November 2013 and you posted to the area where you ask the OP for further information before committing to an answer.
3/27/2023 11:58:30 PM •
Watches
•
Answered
on Mar 27, 2023
How to change to show right day of week
Impossible to answer. On WHAT!!!
All questions need FULL 'make model (what it is)'.
Google
make model manual
Normally on that type of device you have to set the YEAR, and then the MONTH like on my Weather Station Indoor Unit..
..
3/19/2023 11:37:13 PM •
Watches
•
Answered
on Mar 19, 2023
Time not set properly in my watch lasika w-f62
To set the time on your Lasika W-F62 watch, please follow these steps:
- Press the mode button on your watch until you reach the time-setting mode.
- Press and hold the "Set" button until the hour digits flash.
- Use the "Adjust" button to set the correct hour.
- Press the "Set" button again to move to the minute digits, which will also be flashing.
- Use the "Adjust" button to set the correct minute.
- Press the "Set" button again to confirm the time and exit the setting mode.
If you have any trouble setting the time on your watch or if it doesn't seem to be working properly, please consult the instruction manual that came with your watch or contact the manufacturer for further assistance.
3/19/2023 11:07:59 AM •
Watches
•
Answered
on Mar 19, 2023
My dango watch second hand stops some time
If your Dango watch's second hand stops intermittently, there are a few things that could be causing the issue. Here are some possible reasons and solutions:
1. Low Battery: If the battery in your watch is running low, it could cause the second hand to stop. You may need to replace the battery in your watch. Check your watch's manual or take it to a watch repair shop to have the battery replaced.
2. Dirt or Debris: Dirt or debris can get inside your watch and cause the gears to stop moving properly. If this is the case, you may need to have your watch cleaned and serviced by a professional watch repair person.
3. Loose Second Hand: If the second hand on your watch is loose, it could cause it to stop intermittently. A loose second hand can be caused by a damaged pinion or cannon pinion. You may need to take your watch to a professional watch repair person to have it fixed.
4. Magnetic Interference: Magnetic fields can interfere with the movement of the gears inside a watch, causing it to stop or run erratically. If you have been around strong magnets or electronic devices, it could be causing the issue. Try moving your watch away from these devices to see if that helps.
5. Mechanical Issue: There may be a mechanical issue with your watch's movement that is causing the second hand to stop. This can be caused by a worn out gear or other component. You may need to take your watch to a professional watch repair person to have it fixed.
3/14/2023 2:27:20 AM •
Watches
•
Answered
on Mar 14, 2023
Not finding what you are looking for?