Top 20
Siemens SpeedStream 2624 Router (936-2624-001 kit) Questions & Answers
Hi i'm trying to connect my i phone to my wireless
Use an Ethernet cable to connect a desktop/laptop computer to the router. Then, using the PC, you can "configure" the "wireless" capability of the router, and you can establish an SSID and a password. Then, configure your iPhone to _use_ that SSID & password to connect.
3/7/2010 4:52:20 PM •
Siemens...
•
302 views • 0 helpful votes
Hi I have a Siemens Gigaset SE587 WLAN dsl that
Yes you can adjust signal with channel type.
For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Then click on wireless settings and change channel type to 4 or 6 or 11 then save settings and restart router.
Try all 3 1 by 1 then check.
Let me know if you need further assistance.
Thanks for using FixYa.
1/19/2010 4:23:11 PM •
Siemens...
•
888 views • 0 helpful votes
My siemens speedstream 2623 router needs software disks that come
Are you trying to install the router.
You can do it manually without the CD.
Make sure that your computer is able to go online through the modem.
If your computer is able to go online through the modem
Then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.
Click Here for step by step by instructions
2/10/2010 2:45:20 AM •
Siemens...
•
343 views • 0 helpful votes
How can i find my network key for siemens router
You will need to check the wireless settings of the router .
Is there any computer connected to the router with the Ethernet cable?
If not then connect 1 computer to the router and open the router set up page. Once you open the router set up page, you will be able to find the wireless network key.
Use that password to connect to the wireless network
Click Here for step by step Instructions on how to find the network key
12/23/2009 12:02:54 AM •
Siemens...
•
1,024 views • 0 helpful votes
Router was given to me i have no installation
theres a reset button on there somewhere. with the power on, hold reset till you see the router reset then unplug your modem, wait 2 minutes, plug it back in. then plug the modem into the router. then plug the router in.
10/17/2009 11:27:09 PM •
Siemens...
•
306 views • 0 helpful votes
Hello - anyone there?
1. Connect the wireless router to your computer with a LAN cable.
2. Start your browser and enter the router's configuration URL
3. Enter the router setup login and password
4. Change the admin password
5. Go to the wireless settings and change the default SSID and turn off SSID broadcast.
6. Setup encryption key the strongest is WAP2
7. For further secutity measures - turn on MAC address filtering and enter the MAC address of the wireless cards on the computer/s you want to connect to this wireless router.
8. Record the settings you have made and keep it in a safe place and Save the settings.
9. Configure the wireless cards on the computer/s with the SSID and encryption settings of the router.
10. Remove the LAN cable and the computers should be able to connect to the router.
9/28/2009 1:39:00 AM •
Siemens...
•
351 views • 0 helpful votes
I have tried to install the speedstream 2624 to a
I am assuming you had a different device hooked up to the modem directly before, sometimes you may need to call up time warner and let them know as some of the modems do not like to renew IP's properly.
9/9/2009 6:37:31 PM •
Siemens...
•
264 views • 0 helpful votes
I have fogotten how to setup the Speedstream 2624
If you dont want this router to be a DHCP, all you need is disable the DHCP function in this router. So, this router will only act as a switch and will not provide IPs to the other devices.
To disable the DHCP,you need to log on to the web interface of this router . Hope this helps
Thanks
Ranjit
8/20/2009 2:11:41 AM •
Siemens...
•
379 views • 0 helpful votes
Pvc selection keeps changing to dial up mode
- delete the dial up connection on the internet option
- click tools-internet options on the internet explorer - click connections tab, delete all dial up on the box, and select never dial a connection
8/4/2009 6:12:23 PM •
Siemens...
•
328 views • 0 helpful votes
My speedstream 6520 will not let me log in using
Only way is to reset the Router to Factry settings.
Press the reset button on the bottom. But it has two modes one is just a reboot and the other is return to factory settings.a short press reboots it, if you hold it down for a few seconds until the power LED flashes between green and red, then release it, that will factory default it.Then you will be able to login.
5/19/2009 5:09:00 AM •
Siemens...
•
481 views • 0 helpful votes
I have a siemens 6520 and on my dell 6000 laptop i can't access t
Hi there,
You probably have set up some kind of security, and this is where I cant help you as I cant get into your router.
But, when you connect to your router to find out, USE A CABLE, do NOT connect wireless.
You may also find the wireless setup in your dell 6000, but you password and key code will most likely bee a row af stars.
/Teis
Vote if this helped you
11/30/2008 2:04:46 AM •
Siemens...
•
426 views • 0 helpful votes
I'm trying to hook up
you'll have to use your computer to set up a static ip address and open a couple of ports for xbox
what make, model etc is your router?
what operating system are you using XP, XP PRO, VISTA?
12/26/2008 9:53:55 PM •
Siemens...
•
108 views • 0 helpful votes
Problem with modem
If the Online LED on your modem is red, it means that it is not synchronized with the connection that you have from your Internet provider.
Try to reset the modem by holding its reset button for 30 seconds then power it off. After 10 seconds, power it on and observe the Online LED.
If you also have a username and password from your Internet provider, you may set those on the modem configuration.
9/8/2008 3:49:19 PM •
Siemens...
•
351 views • 1 helpful votes
Siemens speedstream 2624
you have to configer your router are you using dsl or cabel inter net
cabel you dont need to set in log on but dsl you do
secound configer your router wireless i think you are are useing dsl speed stream bell use
8/15/2008 4:28:06 AM •
Siemens...
•
260 views • 0 helpful votes
Siemens se 587 router
HI,
You can try manuall setup of da router.
The Default gateway for Siemens Gigaset SE587 is 192.168.1.1. Open Internet Explorer and put the def gateway in the browser.
The default username and password for siemns router is admin.
Click on Setup Tab than Basic Setup on left hand side. Update the details as folloing-
Use – Tiscali data PPPoA Interface
PVC Selection – Tiscali data PPPoA
Authentication – Auto
User Name - Tiscali u/n
Password - Tiscali password
PPPoA Connection Mode- Always On
NAT - ON
And click on save settings. To confirm if the customer is connected, check the status of Online light – which should be green. Alternatively click on status (On top) to check internet status to confirm connection.
Setting Up Wireless connection – Click on da wireless tab on the top.
Ensure that the Auto channel is disabled and the wireless channel is 11, wireless n/w is Enabled and mode is Mixed.
To secure the wireless connection – Click on Wireless Security option on left hand side
If you want the Security mode as WPA than select the wireless security mode, as WPA and enter WPA Shared key which would be on the base of the router. Again click on save settings.
Try connecting to the wireless network again and I m sure it should work..... lemme know if it does.
Cheers
SHADAB
3/26/2008 2:16:44 PM •
Siemens...
•
4,254 views • 1 helpful votes
Not finding what you are looking for?