Top 20 Furuno GP32 GPS Receiver Questions & Answers

Cek the wiring, or change the antene.

Pres power and menu ,or power and enter for a few second.

Change the antene

Please rephrase the question.

This information is not in the GPS instructions.To reset the GPS, you must click on the arrow UP and together on Power.The display shows that the system is reset.Then, the GPS is working properly

Hi,

Go to your GPS company's website, and locate the "Maps" section. It will usually be found under "Support" or "Updates" if there is not an obvious "Maps" tab on the homepage. Plug your GPS into your computer with a compatible USB cord. Follow the steps to installing the USB driver or plug-in from the website. Click the "Download" link, and read and agree to their terms if asked. Then press "Save file" if asked. Go into the "Maps" section of the company's website again, and go to the "Update maps" section. Your GPS should be detected by the driver or plug-in, and this will let you know if there are available updates to install. There may be updated maps available for free, but you may have to purchase them. Purchase and then press "Download." Follow the prompts for accepting the terms of agreement, saving the file, and updating your GPS device. Restart your GPS by unplugging it from the computer and waiting for it to update the new maps. Use as normal.

Hi,

You can download and print the instruction manual in PDF format by clicking this link.

Adobe PDF Reader is required to view this manual. Download Adobe Reader

Hope this helps. Thanks for using FixYa.

Hi!

Your Furuno Does NOT have an internal antenna. You have no choice but to install the external one.

Hope this helps.

pins 2(-) and 5(+) on a 9 pin serial cable, then you need a usb to serial adapter for input into the computer if you do not have a built in 9 pin serial port on you computer because the usb moves the information faster than the gps signal. gps is roughly 4800 baud, usb is moving so much faster you need a buffer

This is a problem in Windows where NMEA data is interpreted by the computer as serial mouse inputs. There are various fixes. If you type Windows mininsterpret NMEA serial mouse into Google you will find lots of info.

I had the same problem with mine - it is 5 years old and very well used. I was told I could send it for repair, but opted to purchase a new unit. You can find service centers on line. The cost did not seem to justify being without GPS and then still having a well used system. This was the best solution for me.

sounds like the problem is with the pilot. You may be expecting too much from nav mode you should check the antenna connector on the WAAS issue
on VX2, are you marking a good bottom on the sonar screen, but have no digital overlaid? never seen it, must be a BB thing

use the yellow and green check for pulsing voltage on wires with digital meter measuring 12V you must turn on the data in the Furuno menus

if it has no signal , measure the antenna output with avo meter. you must see approximately + - 5V. if it is ok.. seems that antenna problem.furuno technician Ozgur CALIK

Question edited for clarity.Page 75 of the manual refershttps://www.manualslib.com/manual/1183586/Furuno-Gp-39.html?page=75Menu - System - LanguageMenu (the U with two dots over it Umlaut) - System - Sprache..

There are set by you to feet, metres, 'F or 'C, knots, kph, or mph.From a bit more reading, depth is Feet, distance is Nautical Miles. Temperature you have a choice.Note: The water temperature graph can beset on or off (See page 11-4.). The temperature scale is fixed between 20-80 °F (0 to30°C).Read the manualhttps://www.furunousa.com/-/media/sites/furuno/document_library/documents/manuals/public_manuals/gp1650fdf_operators_manual_version_m.pdf..

You would obviously be better served if you learned how to google it https://downeastboatforum.com/threads/1650-battery-replacement.12881/

https://www.youtube.com/watch?v=AQW4EoQPM00 hope this helps if so leave some feedback 8]

https://www.admiralty.co.uk/AdmiraltyDownloadMedia/AVCS/ECDIS-Install-Guides/Furuno3000%20User%20Guide%20S-63%201%201.pdf https://www.admiralty.co.uk/AdmiraltyDownloadMedia/AVCS/ECDIS-Install-Guides/Furuno3000%20User%20Guide%20S-63%201%201.pdf

Possibly voltage too low, faulty unit, no power coming to the unit.