20 Most Recent Jensen VM9410 Car DVD Player - Page 2 Questions & Answers

Hello

There are two main reasons for this fault. The first one is confused system control section. The second one is weak Laser Pickup Unit Assembly.
Just reset the system first, to rectify if there is any system confution occured. To reset use the tip of a ball point pen to press the reset button hole, can be located at the front right corner of the player. After system reset, the unit will return to its factory default settings. If the reset is done while a DVD is playing the Dvd resumes play once the reset is complete.
Check out if it helps you or not. If not, put a cleaning disc, and play it two or more times. If there is any dust accumulation on the lens of the Laser Picup Unit, this will rectify the probelm.
If this also not rectifies the problem, the Laser Pickup Unit is defective, and needs replacent. Replace it with samy type and number. OK.

Try this first to see if the remote is sending out the signals. Testing remote control: The remote control puts out IR (InfraRed) signal that human eyes cannot see, to find out if the remote is sending out the signal or not you just point the remote at the digital camera's Lens (Digital Camera can detect IR), you should see flashing light on the camera's screen when any one of the remote button is pushed. If you do see the flashing on the camera, then the problem is in the TV IR receiver or the main logic board; more troubleshooting with scope will be needed to look at the signals. http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm/ Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

try 123456789.

try 123456789

yes, it is possible a bad ribbon cable could be causing all of your problems. you will probably have to go to audiovox.com to get a new one.

Are you using professionally recorded CD's, or are you burning your own CD's?

Professionally recorded CD's are very compatible with most CD players because lasers can read them easier with a transparent, silver-like finish on the bottom of the CD. CD-R's that you buy from the store, for the most part, are a darker blue color, and can be difficult for some lasers to read. Try using CD-R's with a lighter, silver-like finish on the bottom.

First, try using a retail, store bought CD to test if the laser can indeed read the CD. If this works, then the above suggestion may prove to be true.

If this does not work, try using a different CD burning application, such as iTunes, Windows Media Player, Nero, CDBurnerXP, etc. I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

In most venues, it is illegal to have a working video display in the driver's field of view; in other words, they have locked access to the display unless the vehicle is not moving. Making a video display available to a driver in a vehicle that is underway is even worse than texting while driving.

try 123456789

try going to audiovox.com

check the fuse on the back ofthe radio. also chek the radio fuse for the car. make sureyour power connections and your ground is good

DVD's have in them an anti piracy code. If the code from the disk doesn't match with the code from the unit then the unit will refuse to play it. It's impossible to change that code on your unit so you must be sure that all the disks you will try to play have the same region code.

as soon as you open the screen you should see something come up

Does your subs play when you are playing a cd?If yes then you need to check the turn on lead for your sub amp and make sure your jensen deck is putting 12 volt out when your dvd is playing.If it is not you need to find the correct amp turn on wire, if it is then you may have to re equilize your sound when you are playing dvds.

It is possible your dvd mechanism or drive has failed. please remove the player carefully , open the top and check from the point of transit to the slot for the head spindle. check for any dirt/dust/ particles stuck around to prevent smooth transport. look for the loading motor mechanism, drive for friction. correct settings. However is all the mechanism seems in order, then you will have to check on the motor drive, check for signals fromt the processsor to confirm failure of the drive- see if +B is coming to the drive. If not replace. Once the cd goes in , it should land on the spindle and start reading. Helpful.? Good day

yes there is check on www.ebay.com or www.craiglist.com
good luck

Check your Yellow RCA outputs and inputs.They are your video cable connections.

look for reset botton and hold for 3 seconds if it dosent work replace sterio call me for more info at 520-882-8979

Hello,

it is possible that the flex that connects the screen to the player's main board is weak or not well fixed, that's why it fades out.

I would suggest that you get a screw driver, open up the unit and check the screen flex, you can also check the screen inverter. Make sure everything in that part is intact and I believe the problem should be solved thereafter.

Good luck.

Hi megan
Although i have some reservation,i`ll assume your car does`nt have the parking brake wire so here`s the answer to your question;
You do not need to connect that wire but you need to bypass the parking brake function in the menu.
Here`s the parking brake bypass procedure:
1: Go into AM/FM mode
2: Hit "setup" on the remote control
3: Enter 543210 on the remote, listening for the beep for each number entered
4: A new menu will appear. Touch the button that has the hammer/screwdriver on it in the upper left-hand part of the screen.
5: Select Brake bypass to "ON" and hit the "X" near the bottom of the screen.
6: Warning; use the unit wisely and above all safely. A ticket is one thing, causing a fatal accident due to negligence is another.
Hope this help Cheers