20 Most Recent Jensen TS2050J 20" TV - Page 2 Questions & Answers

Hello

Just try one amoung the following codes. I've only these three codes are available with me for Jensen Tv.

{ 0004 _0009 _0133 }

Proceedings

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Note:- If one amoung the above four codes did't work, try the other after the TV is switched off and switch in again after some time, say at about 10 seconds, and try the other. Not enter the code continously without turning it off, after one code won't work. Ok.
__________________________________________________________________________________

If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Hello
There is an arcing takes place inside your tv. It may be from the Line Output Transformer [LOT] to neighbouring components. Please check it with the help of a technician as soon as possible, otherwise, your TV may be in great trouble in future.

if the remote for the all in One tv has a red Okay/Select button then the codes for it are five digits long. And here they are for a Sanyo tv:10154, 10088, 10159

hope this helps.

Try Code 11326, it worked for me on the Direct TV Remote I have with this TV.

Check solder on the vertical output or change it. Dont know # but look for IC screew on heat sink with about 7 to 14 pins.

This is the best solution for your problem as a 40 year experience with wires etc. Go to the source of your cable signal connector . Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires. Vitally

My remote dosen't want to listen to me. The light dose show but it's not doing what i say. Whats the matter with my remote?

see on your remote control and find buttons "power", "code", "enter", "dvd" and next turn on manually your DVD. Now push both buttons at same time "dvd and code" until led light. when the led still ligth release both buttons. Try turn off your DVD using power button of your remote control as many times as be possible until your DVD coming off, after push "enter" button.

Hi.

the TV is in channel lock mode.

To unlock you need to use the original remote.

Do the following:

• Turn on the TV using the original remote control.
• 
  
• Hold down both "Function" and "Mute" on the remote at the same time.
• This should temporary unlock one channel.
• 
  
• Find the channel lock menu, and turn it off.
• If you are asked a key number, enter 0000 , that is the default. On some website, 0711 and 3308 are reported as service codes.

If that does not work, call the number listed on the owners manual, a technical support will follow you step by step.

check timer or maybe has an sleep mode in the TV menu. Good luck!

You will have to go to walmart and get a universal remote to change the channel. About ten dollars.

if you are just have cable from comcast then:

• 0761
  

If you have the dital tuner DTA then this is what you need.

• 
  
  　
  10761, 10050, 10817, 11299, 11933
  

You have to check several things.
1. check outlet for power , then cord , if all this are in good condition working, then your tv has a problem(power supply).

nope

There is the small possibility that you received a defective replacement, however, if you send it back and they test it, you'll know that it is, in fact, the sensor.

I hope I've provided you useful assistance and that this information allows you to make an informed decision as to how to proceed from here. Please be sure to vote on my response. I hope I've earned a good rating from you today.

Please post a comment if you need additional assistance so that I can help you further.

i have a RCA RCR312W universal remote will it work on my JENSEN Model TS2050J 20" TV?

go to www.jensen.com and get tech support.

remote model UNIVERSAL dt008 use code 044

Have you dropped it by accident from a high height or on hard surface? Have you spilled any liquid to it?
Doesn't all the button's seems to work?
Here's a one trick if you have a mobile phone with camera:
enable camera on your mobile phone. Look for a WORKING remote control from the other electronic stuff at your house. Point your remote control to camera lenses and press any button. Do you see blinking red light on your mobile screen? Try this with your DVR's remote control and see if it works. If you are sure about the polarity of the batteries and checked that they are new enough, ther's only two solutions: buy a new remote control according to your TV set model (sometimes it's hard to find) or buy a universal remote control