Kenwood KAC-9152D Car Audio Amplifier - Answered Questions & Fixed issues
What is the p. con on the back of the kenwood
Power control wire - tells the amp to turn on, usually connected to the blue/white or blue wire when blue/white is not present on aftermarket radios. On factory systems you usually want to hook up this connector to an acc source on the car
10/8/2017 4:08:55 PM •
Kenwood...
•
Answered
on Oct 08, 2017
•
3,101 views
WIRE DIAGRAM FOR HOME SECURITY CAMERA
the diagram is supplied with the camera. if not, find the connectors that the camera uses to send the tv signal.find the model number of camera and setup the power connections and route the signal cable to your tv or server or recorder.setup the power cable and connect it to your power source. provide more information about your setup.
11/15/2013 4:34:15 AM •
Kenwood...
•
Answered
on Nov 15, 2013
•
144 views
Kenwood repair manual
I have the Kenwood KAC-9152D Repair Owners Manual. This is my E-Mail address.
[email protected] send my a e-mail. & I will e-mail back 2 U w/the Manual ATTACHED
12/21/2011 12:47:08 PM •
Kenwood...
•
Answered
on Dec 21, 2011
•
335 views
I have a kenwood kac-9152d
make sure it's well ventilated. If there's no air flow, then there is no way of cooling down and to protect itself it will shut off. Make sure the speakers are wired correctly as per amp specs. too many subs or subs connected improperly can draw too much current and shut the amp off, but you will notice this when you turn up the volume to a certain point and the amp shuts down.
9/26/2011 4:17:44 AM •
Kenwood...
•
Answered
on Sep 26, 2011
•
247 views
I did install my amp
Definitely check your wires, you don't want a short under the seats as it can also result in a fire. Also, if the amp is completely covered and there is no air circulation it will overheat and shut off. Make sure it's well ventilated.
9/26/2011 4:08:52 AM •
Kenwood...
•
Answered
on Sep 26, 2011
•
61 views
Amp has power, turns on with stereo, but sub isnt
if you have a protection light that is on it means the amp is in protection mode and wont allow any power to the sub this usually happens when the sub or wiring shorts out or if there is an internal failure in the amp or if its overheating. check the wires and connections and test your sub on another amp.
5/13/2014 12:36:45 AM •
Kenwood...
•
Answered
on May 13, 2014
•
407 views
When i power on the unit, it comes on for a second, but shuts off
that is the way it works, I assume it is a car amplifier here,please accept my apology if I am wrong.Normally these amps are powered on by the radio/cd player.It has a wire which connects them together which wakes up this amp when radio/cd is powered on.Hope I have answered your question.
6/29/2010 10:51:22 PM •
Kenwood...
•
Answered
on Jun 29, 2010
•
231 views
I have a 1976 kenwood am fm stero receiver, the
A stereo or amp, either one should have a fuse, fuses for radios would be in the wiring harness behind the radio deck. An amp fuse should be obvious were they insert in the fuse blocks by the amps main power cable connector. If you see that all fuses are fine then check your ground wires if not then your radio is bad.
6/20/2010 2:45:39 AM •
Kenwood...
•
Answered
on Jun 20, 2010
•
125 views
How to replace the belt
1st you have to open it with removing bolts of it. then there is lock with the belt it can change easily then change the belt
6/11/2010 6:34:23 PM •
Kenwood...
•
Answered
on Jun 11, 2010
•
509 views
My Kenwood KAC 9152D Amp is hooked up to power and
Check your ground. Make sure you sand off any paint where you grounded the amp. Also did you hook up the remote wire? It's the blue wire on the back of your headunit. Some say remote wire, others say power antenna either one will work. Sounds like one of the two...hope this helps.
6/8/2010 3:54:12 PM •
Kenwood...
•
Answered
on Jun 08, 2010
•
345 views
How to connect a amp to a 1994 celica
put a fuse on your amp power wire bout 12" from battery, run wire to your back of car make sure you have a good ground wire hooked up and a remote wire from your head unit (blue) to the amp and run the speaker wires and you should be good to go. make sure you get the right gauge of wire for you amp. hope this was helpful
5/11/2010 12:44:37 AM •
Kenwood...
•
Answered
on May 11, 2010
•
88 views
Amp will not turn on
make sure to double check your remote wire and to see that it is connected properly
4/27/2010 3:36:42 PM •
Kenwood...
•
Answered
on Apr 27, 2010
•
117 views
Amp not getting sufficent voltage
Does the car start with the voltage dropping like that? Sounds like a bad battery. A battery can show 12.6 volts and as soon as you put a load to the battery the voltage will drop. I would change the battery and see if that helps. Also check your alternator. Get a DMM set to DC volts connect it to the battery and see how far the voltage drops when the cars running. You should see something like 14 volts or so. If it drops below 11 volts you may need to upgrade the "big 3" wires...hope this helps
4/1/2010 6:05:42 PM •
Kenwood...
•
Answered
on Apr 01, 2010
•
154 views
Not finding what you are looking for?