Number 2 can be found on the internet advertisement.
Number can only be accessed IF you are a licensed or authorized
service center. Please contact them for more technical information than
can be listed in your guide.
yellow-constant red-accessory if there is a light green,pink,or brown one is is us for brake , purple/white -camera or green/white green/black-left rear- spk- solid/green-left rear-spk+ purple/black-right rear-spk- solid/purple right rear spk+ gray/black-right front spk- solid/gray-right front spk+ white/black-left-front spk- solid/white-left front spk+ brown or orange if any phone mute black -ground pink/white or purple/white or green/white-reverse camera''
Here is the solution for turning off the demo mode:
Please carry out the following procedure:
1. Press (SRC) button repeatedly unit "STANDBY" is displayed 2. Press and hold (MENU) button to enter the Menu System 3. Toggle the (CONTROL) knob upwards unit "DEMO ON" is displayed 4. Press and hold the (CONTROL) knob unit "DEMO OFF" is displayed 5. Briefly press the (MENU) button to exit the Menu System.
Common Kenwood Security Codes Many Kenwood radios are configured with the same security codes:
KCAR - This seems to be a "backdoor" to some Kenwood models. 3051 - This is the security code which is printed in the manual of many Kenwood models. 1234 - This is a security code commonly chosen by Kenwood owners. Entering Your Kenwood Security Code If the car battery fails or is disconnected, the Kenwood will ask for the security code.
The
procedure to enter your security code differs on various models of
Kenwood car stereos. Here are three of the more common procedures:
Type 1 During
the code request mode, while holding the DISP key depressed, press and
hold the Volume UP or DOWN key for 3 seconds until the "..." display
disappears. Enter the security code using your Kenwood remote. Type 2 Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear. Enter the security code using your Kenwood remote. Type 3: Model# DPX-4020 and DPX-4030 Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'. Enter the security code using your Kenwood remote. Entering Letters on your Kenwood Remote To
enter a letter using your Kenwood remote, press a button once for the
first letter, twice for the second letter, and three times for the
third letter -- then press the Track Up or Next Track key to send the
letter.
To send the letter 'A', press the 2 key once and then
press the Track Up key. To send the letter 'B', press the 2 key twice
and then press the Track up key.
Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.
The key sequence to enter the security code KCAR is:
5 5 Track Up 2 2 2 Track Up 2 Track Up 7 7 Track Up Your Kenwood should then enter tuner mode.
A Security Code Bug in some Kenwoods There
is a reported bug in the security code handling of some Kenwood
stereos. In models with thie bug, the security code is stored
incorrectly. The workaround is to enter the wrong security code.
In
models with this bug, you have to decrement the third character of the
security code by one. If your security code was 1111, you would enter
your security code as 1101. If your security code was 9999, you would
enter 9989.
There should be an option on your head unit to turn safe mode off. If this fails, you need to trace the parking brake wire that runs from your head unit back to the parking brake switch and disconnect it. This is illegal in some contries and therefore not recommended.
did ya sdo it self cuz if soo you probly forgot to hook up the ignition wire because cds will eject while car is off check for power at ignitiion wire the red one coming from deck harness and then get back to me
