20 Most Recent
Panasonic DMR-EH50 DVD Recorder - Page 2 Questions & Answers
Cannot get remote to erase programme I have seen
If you are getting an error screen with "cannot edit while ext link active" or similar, you can kill this by going into the screen for recording a new programme and THEN pressing ext link button. Found this by trial and error. Once this is off you should be able to edit in the direct navigator view. You can't switch off ext link in this view for some reason.
Vivienne
10/10/2011 6:54:35 PM •
Panasonic...
•
Answered
on Oct 10, 2011
When i press remote all I get is remote DVD 3 on
The remote and the unit are using different command codes. You can try this:
Press and hold [ENTER] and the number 3 button together on remote (while pointed towards unit) for 10 seconds, then release. This should restore the remote command to your unit.
It might not help, but it's worth a shot.
4/26/2011 9:20:28 AM •
Panasonic...
•
Answered
on Apr 26, 2011
Panasonic DMR-EH50 DVD Recorder
Impossible to
Hi,
how long have you been using the player and has it ever accept blank DVD-R discs in the past.
The problem might be as a result of weak laser (lens) or the blank discs inserted might not be compatible with player.
When
the laser(lens) of a player becomes weak, it will not be able to read
blank discs. It only takes a very strong laser to read/accept blank
discs. If it happens that the laser (lens) is the cause of the problem,
then it means you will need to replace the laser (lens) to a brand new
one to be able to read blank disc. Though the player might be playing
DVD and CD, note that blank disc is stronger when it comes to reading
from the laser (lens), it requires sharper laser. I hope you understand
this.
Concerning the incompatibility issue, I
hope you are aware that there are various kinds of empty DVD discs such
as DVD +, DVD -, DVD RW. Try any of this empty DVD discs as one of them as to be compatible with this DVD recorder.
Amongst
the two topics discussed above, one has to be the cause of the problem.
So its up to you to figure out which is the cause of the problem.
Good luck.
2/13/2011 7:27:41 AM •
Panasonic...
•
Answered
on Feb 13, 2011
While trying to save parts
Highlight the recorded program on Direct Navigator then press the Sub Menu button on the remote, then select "Shorten Title". Press (Enter) at the start point and end point of the section you want to erase, then use the up/down button to select "Next". Then, select "Erase" to delete the unwanted sections. Repeat this process for all unwanted parts, then select "Exit" to return to Direct Navigator.
11/20/2010 3:08:27 PM •
Panasonic...
•
Answered
on Nov 20, 2010
Remote not working. Unit is
If unit is set to remote-2 then you need to change remote mode on remote itself as per unit to communicate, press and hold ENTER and 2 buttons on remote for 3 seconds to change remote mode on remote control, now unit will accept remote commands.
If you want to change remote mode on unit, go to menu and change remote option in unit then again change remote control mode accordingly.
Thanks.
11/15/2010 9:00:19 PM •
Panasonic...
•
Answered
on Nov 15, 2010
Code to use ir-blaster with dmr-eh50 to control
I know your model of comcast (Thompson) DTA can be controlled with at least some IR blasters (specifically the hauppage for SageTV) using the Motorola code set 0080. (I am told the protocols are called XMP/Dreambox, but this knowledge won't help your situation.)
I recommend you run through the IR-blaster setup menus, choosing Motorola code sets. If this doesn't work, select 'unlisted' and allow the panasonic recorder to run through all the set-top box control codes it knows. If it still doesn't work, then the DMR simply does not know the code for your DTA & I do not believe that it can be taught new tricks.
That said, I did review the docs for a firmware upgrade for the DMR-EH50, & while nothing was mentioned in that documentation regarding increased blaster compatibility, it wouldn't hurt to update your recorder to keep it as current as possible & maybe it will help after all.
I hope that helps.
6/30/2010 4:49:29 AM •
Panasonic...
•
Answered
on Jun 30, 2010
We have a Panasonic DMR-EH50 DVD player/recorder.
The message displayed means that the remote control and unit are not communicating and the remote needs to be programmed. To program the remote, press and hold the same number that is displaying on the unit and the [ENTER] or [OK] button for more than 2 seconds. For example, if the unit displays “SET 2”, press and hold [2] and [ENTER] or [OK] for more than 2 seconds.
4/25/2010 1:53:39 AM •
Panasonic...
•
Answered
on Apr 25, 2010
My recorded is linked to a tv with a Freeview box
if you TV has a feature called "Monitor" out, then you can take a "Feed"out, via, The AV, link, the Yellow, Video, Red & White Audio. wiring color to color, and selecting EXTERNAL IN on VCR. If this feature is available, whatever is on screen, is displayed out of that "Monitor Video & Audio Socket"
Get a TV manual and a VCR and have a look it will show you how.
3/23/2010 8:52:12 AM •
Panasonic...
•
Answered
on Mar 23, 2010
Not finding what you are looking for?