Top 20 Sanyo DS27510 27" TV Questions & Answers

No. It is meant for service adjustments only.

Fault to the main power supply section circuit. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/

0173,0118,0138,0182. Try these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common set-up codes to check with TVs and other devices are given, in the order of the "device's brand name" in alphabetical order. Pull up older posts. Surf the site with patience. Surf the sites by type in the brand name to your set, in its search box. http://electronicshelponline.blogspot.com/ http://remotesearch.blogspot.com/ http://electro-medical.blogspot.com/ http://electrohelponline.blogspot.com/ Type in the brand name of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts. It will make surf easy.

Sounds like picture have been shifted horizontally. If you want to adjust the horizontal position, you have to enter its service mode option, and to change the data value there. Contact any service technician. This is a skilled work. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done. NB: Please read and understand well, the instructions to enter the service mode, before you begin. Be very careful. Note how to "EXIT" the service mode; after entering and adjusting data. This is very important. Type in the brand name of your device, in the search box [at the top right] of the display window, and press enter to get all related posts. It will make surf easy.

If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/

If you see thus, check the antenna connection for firmness first. If it seem correct, the tuner to your set is faulty. Does not process the RF signal. There is no repair to this, other than replacement. Contact any service technician to replace it. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

It sounds that the synchronization separator section is faulty. In all modern sets, the section will be a circuit part inside the main IC. Therefore, check out, and replace that IC.

do you mean you want to use the tv not through cable program?. ok just remove the cable box then hooked up an air antenna to the RF tuner. then change the settings in the tv select air not cable.

Not possible unless set has a source or input button on the front or side.

. There is a high possibility that the components over a period of heating and cooling, tend to bring on a problem of dry soldering. So my advice is to check the set for some loose joints that have played on to give you these erratic shut downs or poor performance. The best way to check for loose connections is to tap lightly when the set is powered on, if there is change while tapping then it seems that there are DRY solder joints. Remove main plug, the covers - with caution of high voltage, check for dry joints, and use a good soldering iron to solder all suspected points. Sometimes the fault occurs when the set warms up; if so you can simulate the heat using a hair dryer on the suspected areas, try with the power supply, distribution, Processor controller, driver controllers on the A/V related sections. Also the use a FREEZE-IT spray can simulate the components to cool and show up the fault. It can also be related to WEAK ELECTROLYTIC capacitors as the value can reduce in time.

V guide or V Chip settings might be coming from your signal source rather than the TV itself. You might want to try contacting your cable or satellite company.

your bulb is going out

Try using the Channel up-down to scroll through.
Owner manual: http://tv.manualsonline.com/manuals/mfg/sanyo/ds27510_1.html

Please leave rating if it helps.

Unplug the TV for 20 minutes to see if it will reset.

Do other functions on the remote work properly?

Thanks!

3year remote..individual much used buttons can wear out,try new remote

To be honest, you can't. Purchase a universal remote control. I just bought one from Walmart for $4.94. The remote will control everything for your TV.

Yes,but that involves removing the back panel and soldering a new one to the pc board.

check if the tv set on sleep timer. if is not thers a lose connection in the power supply of your tv. get a proffesional ttv technician to check-up the power supply sometimes leak parts are encountered in the power suppy.

in the remote control press the bottom display.