Top 20 Sanyo DS27800 27" TV Questions & Answers

~ $360. http://electronicshelponline.blogspot.com/

If the remote control is a universal remote control, in most cases, the input selection button won't work. If so, the only thing you have to check is, synchronise the remote control with an other set-up code to your TV. If you wish to get more details, check the sites linked here. Setup code list, and setup procedure to many popular brand remote controls are given. http://electrohelponline.blogspot.com/ http://remotesearch.blogspot.com/ Selecting the view option, either to Mosaic / Flip card, can be selected by the drop-down list, by the top left of the display window, will make surf easy. google.com/+GopakumarGopalan

To make a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. This must make it a hard reset. If you wish to make a system reset, you have to enter its service mode option. To know more about this, check this link. It has details about how to enter, adjust and exit the service mode, to many brand TVs. http://electronicshelponline.blogspot.com/ Pull up previous posts by its left sidebar, or type in the brand name and model number to of your set, to its search box, and press 'Enter' or view it in Mosaic / Timeslide option.

Look for a round cable connect in back of set. You will need different connector for antenna. Go to store like radio shack for info and parts.

There is no option to do this without its remote control.

U using the RCA AV cable Y,R,W plug into those tv video input holes wright?Tries another RCA Y,R,W AV cable,see if it work?U have tools like a soldering iron,a roll of solders,also can u do basic soldering?Tries take some alchahol clean the Yellow input hole and take the tv aparts resolders it connections joints,now the video out it should work again,if not yellow input hole might be shorted require replacing.

Check the tv manual buttons,have a input button.No.Try website like Remotes.com to buy an original remote so can find out with input ur VCR/DVD device unit hook up into like video input like 1 or 2.

You've probably locked out that channel. Go to menu and add the channel. See if that helps.

NO VERTICAL DEFLECTION MEANS YOU HAVE A HORISONTAL BAR IN THE SCREEN?, Check the power supply for the correct voltage to the vertical circuit, check the vertical DRIVER circuit, check the conductivity of the YOKE (vertical winding) on the neck of the tube

if you have a VERTICAL bar in the screen (common mistake) check all of the above relating the HORISONTAL circuit

good luck!

I'm not sure if this will work with your TV. Some TVs will go to the other inputs if you go all the way through the channels and keep going.

Normal aspect ratio is 4:3, and the wide aspect ratio is 16:9. If you play a game meant for 4:3 and you change the TVs aspect ratio to 16:9; part of the picture will be cut off. It is not the fault of the TV.

replace or reseat connecting leads?

hi,

any big box store or radio shack should have a suitable replacement. your cable or directv or dish remote can be programmed for the tv depending on which provider you have. go to the website of which one you have and go to "remote codes" section if you dont have cable or dish then go to walmart and get a universal. the more you pay, the more features you will get. look closely at the packaging. thrift stores usually have a whole wall of old remotes in bags you can start looking there too. if you can find a sanyo vcr it may have some tv functions that might have the tv codes on it.
jm

you need to reprogram the channels on the tv,thats why the tv cant get out of the video 1

Please go to this link to get the code for your remote:

http://www.p4c.philips.com/cgi-bin/dcbint/urccf.pl?slg=EN&scy=US

This hopefully is resolved for you, but if it has not been, or you have any questions about it, here are some steps. Follow the link below, and it will show you how to program the remotes again!!!! Hope this helps!!

http://www.dishnetwork.com/SupportSection/remote-setup


Becki Barned
DISH Network Customer Service

I assume you want the code for the service adjustments which is to hold the Menu button on the TV down then plug in the set and service menu comes up.

If you need a code for a cable box for a sanyo remote check your users manual or i need more info about the cable box.

If you need a code for the sanyo for a 3rd party remote control you need to specify the remote. Or check its users manual.,

Yes, it will certainly have a fuse, probably near where the power cord attaches to the main circuit board. Be careful if you open it up though. Even if you unplug the set, you can still get a good shock from the set's capacitors.