20 Most Recent Sanyo DS31520 31" TV - Page 5 Questions & Answers

try these 3 digit numbers.sorry there is a few of them,but one of these should work.018.020.041.049.060.065.102.107.131.152.195.198.209.320.379.391.408.421.481.

You can try the Channel up/down but if that does not work it looks like a trip to your local radioshack or store with universals. Also there is another solution actually two..

Hook a good old VCR up to that baby and hook the cable to the VCR put the vcr on 3 and bingo or www.remotes.com for your orginal factory remote.

Hope this helps please be considerate when you leaving you vota and feedback. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Change the input to cable or TV. Look in the manual and use your remote to scroll through the menu....

http://www.retrevo.com/support/Sanyo-DS31520-TVs-manual/id/17567dj494/t/2/
It is all explained in pictorial form in the user manual above.

http://www.fixdevice.com/smanuals/file/6441.html
Inside is circuit diagram

hit display botton

This is the best solution for your problem as a 40 year experience with wires etc. Go to the source of your cable signal connector . Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires. Vitally

is easy to program if you don`t have the # code turn on you tv and just hold the the code seach or set up button until the red ligth stay on and then selec what do you want to program tv,vcr,etc push and let it go then push power until you tv turn off then push enter to safe the code if you push one more time after turn off you tv you have to star over

In order to answer your question, I will need to know what type of remote you have. The code settings are different for almost every type of control. If you wish, you may repost the question with the remote manufacturer and model. Thanks for posting! sincerely, Der Strom

check first if the problem is the spr or in the entire ckt. reply this and we will trouble shoot step by step.

Try one of these, 017,023,027,038,066,080,091,098,123,125,126,202,203,205,206,207,208,209,210,211,154,159.... hope this helps..

Turn TV on, on the remote press TV, press and hold SET until the light blinks once,pauses, then blinks twice,release. Enter one of the three digit code,s ,it will blink twice. Aim the remote at the TV and press POWER, the TV should turn off, if not, try the steps again using a different code until you find the one that works... 017,023,027,038,066,080,091,098,123,125,126,202,203,205,206,207,208,209,210,211,154,159...hope this helps..

http://sanyoservice.com/partsinquiries.cfm

go to that site and search your remote codes , Or if you send me the model number and brand of your remote I can help you

[email protected]

Try website 1-800-Remotes Factory original.To buy an exact remote.

Try 0154.