Top 20 Sanyo DVW-5000 DVD Player/VCR Questions & Answers

https://www.videohelp.com/dvdplayers/sanyo-dvw-5000/1371

Hi, this is a bit basic, try turning of for about 1/2 hour, to enable to discharge, then try again. ( I have used this on industrial installations, with far to complex computers stuff inside, and that mainly works)

Commercial DVD disks are "keyed" to a specific "region". USA is in "Region 1", and Europe is in a different region. Some DVD players allow you to "switch region", but only up to FIVE times, and then it "locks" into one region.

Does that specific DVD work in some other DVD player? Does that specific DVD work in the DVD-drive in your computer? Dirty disk?

HelloSend your Email address to me by Fixya comment box. I've the user manaul to your device. I can't send it to you by this window as it does not allow me to upload PDF files by it. If you send me your email ID, I'll send a copy of it to you by return mail. OK.

We lost our original remote also. We got a generic remote. It came w/instructions & a list of brands/devices that it will work with. I found Sanyo on the list & entered the code associated w/Sanyo into the new remote & presto. We were using our DVW 5000 again.

The link to the Instruction Manual for a Sanyo DVW-5000 may be found by clicking here. It is in pdf format and would require Adobe Acrobat Reader.

It is most likely that the pinch roller will need replacing. Once these become glazed (shiny) the tape slips over them, resulting in 'chewing' as the edges of the tape ride up or down the capstan shaft and into the top or base 'rabbit' of the exit guide nearby. Replace the roller, clean the tape path (capstan, guides, heads, take up arm, etc., *gently of course*) with alcohol solution or methylated spirit - do not use q-tips to clean the drum.

VCR should be OK after that. No further repair should be necessary here, and rubber pinch rollers for VCRs are not expensive to order as a generic part for this model.

here is a basic diagram of cable connection from a cable box to a vcr and to the tv.

Hello,

was the VHS recording before the new high definition TV was installed? Or are you trying to say that the cable company has tempered with the settings of the VHS?

Probably, the cable company, has removed the cable for the player. Check the back of the player and let me know if the cable between the player and the TV are intact.

The above needs to be verified for accurate solution.

I look forward to your reply.

Bye for now.

This maybe too simplistic but are you sure you have the right command buttons toggled try to set the player to VCR and not dvd.
Set the player to VCR with a tape in it and press play. I hope this works for you

This sounds like a problem with the mechanism of your player,it is probably stuck.

What you should do is to open up the player and try to open the door with your hand by pulling it,check to see what is stopping it from opening and clear the object stopping the door from opening automatically

Please note that it might just require oiling the door wheel to make the door open and close automatically.

Did you finalize the disc when you finished on the Magnavox? That should do it.

I think the answer is simple. You have a DVD player with a VCR Recorder/player. You can't record to a DVD Player. Sorry

the reason is because your dvd player inside got caught on something in side and now won't work for your disc it might even be off track...

NO.

Hello,

Yes you have to plug the red and white video cords before your movie can play.

You can connect your DVD directly to your television, then after seeing a movie you can reconnect your cable, since you cant see the movie and the cable at the same time.

But if you want to see a movie from your DVD using the dvr player, then you have to connect the audio-video out from your DVD to the dvr players audio-video in, then connect your dvr players audio-video out to your televisions audio-video in, then you ensure you get the proper frequency channel on the dvr player where you can view the DVD player from.

Then you can watch a movie on the DVD using the dvr player.

Take care

Sounds like the tracking unit failed on you. This would cost more to fix it then the unit is even worth sitting right now. You can grab one of these units for under $75 bucks. For what its worth you might want to try to clean it with a kit but I feel this error is more serious then a cleaning kit can handle.

Hate to bring bad news but why tell a lie and you be upset?

Thanks and please do click the accept button for my efforts. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Hi, if ithere is no button on the front of the unit or on the remote, then simply setting the unit to standby with either power button should make the unit enter the timer record mode. (This will be indicated with TIMER or a small red clock symbol in the display providing all the conditions have ben met. i..e clock & timer correctly set, tape in machine, etc)

Hi.

Try entering the model number here to see if the model is available. Full model number is printed on the tag at the back of your combo.