20 Most Recent
Dell W3000 30 in. HD-Ready LCD Television - Page 9 Questions & Answers
Hi, i had remove vista
The issues that you will have when DOWNGRADING is the availibility of drivers that can run the newer hardware. Hardware capability has exceeded the ability of XP. Sometimes the boys at HP can direct you to drivers that will work. I strongly recommend against downgrading. If you have Vista, you will like Windows 7 much better, it quits asking for authorization on everything.
I had a virus and
Download all drivers and and original SW here.. Find your model by tag number, http://support.dell.com/support/downloads/index.aspx?c=us&l=en&s=gen
It wont let me download to the keychain says pic
I don't know which Keychain Digital frame you have but they all only hold Jpg files, some will hold a bmp file as well. How large is the file you are trying to download? They can hold 4 to 8 Megabytes of memory. The picture size needs to be 128x128 or less. I wish I could help you more!
My Dell flat screen LCD
You have external speakers plugged in and it still doesn't work? This means the sound board on your TV has failed... it is repairable but expensive. Not worth it in my opinion on this size of TV.
Thanks, let me know if you have any questions or concerns, just reply to my answer here and I will be right back with you.
Tim
Where can I get my
IF you are looking for a local repair guy, please get me your zipcode so that I can look up the directory and get you the list of techs in your area.
We have sound but no
Model? see some of my Dell TV albums.
First, look at the screen in darkened room to see if you can see any slight glow from the screen, if it does, then the problem can be the T-CON (not getting the 12vdc) or the main logic board not feeding the signals to the T-CON board.
if not, next place to check will be the power supply module, make sure it has 24vdc which is required by the backlight inverter to work, the reason for not having 24vdc can be from bad DC filter caps (leaking/bulging top, high ESR) or short circuits in the inverter board which will cause the 24vdc supply to go into shutdown mode, so you may have to disconnect the power cable that feed the inverter board to see if the 24vdc will work without the inverter board hookup, you will need to apply about 3~4 amp of load to the 24vdc to make sure it can handle that. There are fuses on the backlight inverter boards also. So there is some troubleshooting you will have to do to find out the causes of the problem you are having.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:
Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums
http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.
Please post back what you find.
LOOSE VIDEO AFTER APPROX 6
The tv overheats and a connection inside the tv breaks. You will have to open the back of the tv, clean very gently but thoroughly everything in sight and reseat every single connector.
My flat panel tv w5001c
Hi,
your TV is having a power problem. The power supply board is defective that's why the TV won't power up. Its receiving power but it cannot transfer the current to the necessary part of the TV because a capacitor, diode, etc may have been faulty. Until these bad components are replaced, the TV might not come on.
If you know about TV repairers, I would suggest that you open the TV and read the power board/panel with a meter, detect the bad component and replace it. Take note that TV stores a lot of current that can shock, so leave the TV for a while before you open it.
If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you.
I wish you good luck.
I have a 37" dell
This is normal procedure; after that the control processor should load the firmware and the last channel selected will appear. If the tv is stuck on the welcome screen it's because the processor can't load the firmware - either because the processor itself is defective (replace the control board) or somehow the firmware was corrupted. To find which you must connect the tv to a pc using the special firmware adaptor. Unless you have one you must take the tv to a dealer specifically, since unaffiliated repairmen rarely have them.
Not finding what you are looking for?