20 Most Recent RCA RS2650 Shelf System - Page 5 Questions & Answers

Request the manual from RCA.

https://www.fixya.com/support/t13862396-set_clock_rca_model_rp_5606_b_disc_clock

I love the form of your question, as I wanted to wing the sucker myself, but got online before I actually pulled an Office Space on it. I found nothing, but I DID actually figure it out. Not super intuitive though. To set the time: Hold down the memory key in the middle until the number flashes. Use the arrow up/down on the right to set hour. Press Memory key again, repeat with arrow keys to set minutes. Hit memory key again. Alarm: Press/hold the Alarm button until the Alarm 1 or 2 flashes and press the side you want, 1 or 2, to set. Arrow time up/down, then do minutes, press alarm 1 again, select alarm or tuner, press alarm 1 again. Now I need to see if it will work in the morning. I know the flipping time is set though! Good luck. If you wing it, please post photos! :D

Likely short somewhere, speakers or amplifier

This could be a lot of things. IT could be a switch connection or a chip that has failed, could be a solder connection that is bad. Without proper equipment to send a signal into the unit and trace it, you may not be able to find the problem.

You did not list the model numbers of either item but I can tell you that the new televisions use HDMI to send and receive audio. With that in mind, there is no way to do what you want to do unless you buy a converter like this one: https://www.amazon.com/AGPtek-SPDIF-Extractor-Converter-output/dp/B00ECTHIKK

Slide the switch Lock/Wake/Clock on the top of the unit to clock position. Press REV or FWD to set the clock time. The time decrements or increments will follow by a faster rate when you press and hold the buttons. The ":" between hour and minute time flashes when you are setting the time. https://voxxintl.zendesk.com/hc/en-us/articles/225310027-Operating-the-RCA-RP5420-Dual-Alarm-Clock-Radio

This is a component failure. A lot of pre amps use OPERATION AMP chips. Finding the issue involves a lot of time and troubleshooting with special equipment.

I bought a new universal remote because my RCA Home Theater remote went bad,took a few hours to figure out that I had to use the Audio remote code on the list.I have RCA RCRN06GR Blu-Ray Home Theater. The audio codes that came with my new remote are 41609, 41254, 41390, 41511, 42041. I believe it was 41254 but try them all if it doesnt work.

First the music files need to be converted to mp3 file format before copying to your MP3 player. Please click on this link for instruction on converting music files and copying to your player :-
http://www.fixya.com/support/r5798418-creating_transferring_mp3_music_files

Yes it is possible but be carefu

Did you have more detail to the question? Seems to be missing something at the end. Please Edit the question or Add Information or Comment to flesh it out What in specific are you hooking the microphone into? Amplifier, preamp, mixer, receiver? It will depend what your input is expecting Have you put in new batteries in the mic? Do you see that the receiver is receiving the mic signal? Is there any sound at all when you plug the output of the receiver into the input of your { fill in the blank } ? Setup guide https://www.akg.com/on/demandware.static/-/Sites-masterCatalog_Harman/default/dw3aa903a6/pdfs/AKG_WMS40_Mini2_Quickstart_Guide.pdf

++++++++++++ https://www.manualslib.com/manual/313341/Rca-Rs2052.html

https://www.manualslib.com/manual/313417/Rca-Rp-7925.html

DVD players normally don't have amps built into them. If you need to connect the DVD to amp (AV) then it will need to be connected either via an RF lead connected via RCA sockets marked RF OUT on the DVD player and one on the AV marked RF IN. If the AV has an optical in, then you can connect the DVD to that for better quality sound. You might also need to change the sound output settings on the DVD player to the correct one you are using. Missing speaking sounds are the result of a lack of a centre channel speaker. If your AV doesn't have one. Then you will have to use the stereo only setting. If the DVD player is only currently connected via the standard RCA left and right jacks, you will only get stereo sound.

If you're trying to put an equaliser in between a source and an preamp or integrated amp, the amp needs to have tape OUT or dubbing OUT connections. This will go to the eq's IN. Then eq OUTs should be connected to the tape or dubbing IN on the amp. When playing any source you set the amp's source selector to tape or dubbing IN and now what you are hearing is coming through the equaliser.

There are lots of methods. You can resort to online music download website, chrome extension, or music download software. Follow below steps, to know the detailed information. Leawo Music Recorder is a super recording software to help you record various kinds of music from multiple sources like online music like YouTube, computer audio, and built-in input audio. The recorded music files will be saved into an output format of MP3 or WAV. 1. Run Music Recorder on your computer and enter the recording interface. Audio source should set firstly before music recording. In order to record the music from YouTube, we should choose the option "Record Computer Audio". 2. Click the red button "Start" to make Leawo Music Recorder begin to work. Then play the music on YouTube. You should note that the music recorder should work prior to playing YouTube music. If you want to decide the start and duration time of the recorded music, just click the icon button "Task Scheduler" then you can finish this customized setting as per your requirement. After the music has been recorded from YouTube, you can use Leawo iTransfer to move the recorded music from computer to your iPod Leawo iTransfer is a professional transfer program for transferring files between iOS devices, iTunes and computer. Various kinds of files are supported by this software such as music, apps and photos, etc. 1. Run Leawo iTranfer after you have downloaded the music on your computer. Connect your iPod with your computer via USB cable. The library of your iPod will be detected automatically and shown in the left sidebar of the window. 2. Import files to the software from computer in the following four-way: I. Drag and drop the music files into iTransfer directly. II. Click the button "Add" on the upper part which is beside the left sidebar. III. Click the button File > Add > Add File/Add Folder on the top right corner of the window. IV. Right click on the library and select Add File or Add Folder. 3. A pop-up dialog will be shown once you finish adding files and press the "Transfer" button. The name and the quantity of the transferred files will be demonstrated to let you know the transferring percentage. Remember not to disconnect your Apple device to your computer until the transferring is completed. For more details, check: How to Download Music from YouTube to iPod

This could be anything but I would guess you probably have a short in the system.If you could give me more information I may be able to help you better.

hardrocko

Hello Kathie, indicate model of the equipment that you are commenting, to be able to find the best possible solution I wait your answer Greetings Franco Dosil Hola Kathie, indica modelo de los equipos que estas comentando, para poder encontrar la mejor soluci?n posible Espero tu respuesta Saludos Franco Dosil

https://www.manualowl.com/p/RCA/RP3721/Manual/54944