Xterra Fitness TR3.0 Treadmill - Page 7 - Answered Questions & Fixed issues
Where can I find my treadmill speed sensor?
If it's not in the typical location, there are a few other places it could be, such as near the front roller or underneath the motor cover. You could also try doing a visual inspection of the machine to see if you can spot any wires or components that look like they may be connected to the speed sensor. If you're still having trouble, you could try reaching out to online forums or communities for treadmill enthusiasts to see if anyone else has had a similar issue and found a solution. I hope this helps!
2/14/2023 9:46:04 AM •
Exercise &...
•
Answered
on Feb 14, 2023
•
79 views
My life fitness elliptical keeps paUsing every 30 seconds, how do i stop it
I had the same problem with my 91X, put in a fresh battery and checked the magnet on the large wheel but it still did the same thing, finally i called the manufacture and the guy said its most likely bad or dirty brushes in the alternator, I took a picture of the wires, disconnected them removed the brushes cleaned them with acetone, reassembled and bam! worked like a charm, hope this helps someone
2/9/2023 10:04:04 PM •
Exercise &...
•
Answered
on Feb 09, 2023
•
2,130 views
Urevo treadmill - knocking noise
A knocking noise coming from the rear roller of a Urevo treadmill can be caused by several issues. The following are some troubleshooting steps you can try:
- Check for loose bolts: Make sure that all bolts and screws that hold the frame and the roller in place are tight and secure.
- Check the belt tension: Ensure that the belt is tight enough. If the belt is too loose, it can cause knocking and other noise issues.
- Check the rollers: Make sure the rollers are not worn or damaged, as they support the weight of the belt and can affect the alignment of the belt.
- Check the deck: Make sure the deck is not damaged or worn, as this can cause noise issues as well.
If the noise persists after trying these steps, it's best to stop using the machine and seek assistance from the manufacturer or a professional repair technician. Using a machine that is making a knocking noise could potentially be dangerous and lead to further damage.
2/3/2023 2:00:48 AM •
Exercise &...
•
Answered
on Feb 03, 2023
•
755 views
When I turned on my pro form 540s treadmill using the magnetic key it turned on like normal,
The issue with your ProForm 540s treadmill is likely due to a problem with the speed control circuit. Here are a few steps you can try to resolve the issue:
- Check the speed sensor: The speed sensor on the treadmill can be damaged, causing the control board to shut down the machine. Check the wiring and connections to the sensor, and replace it if it's damaged.
- Check the wiring: If the wiring connecting the control board and motor is damaged, it can cause the control board to shut down the machine. Check the wiring and connections for any damage, and repair or replace as necessary.
- Check the control board: If the control board is damaged, it can cause the machine to shut down. You can try to reset the control board by unplugging the machine from the electrical outlet for a few minutes and then plugging it back in. If the issue persists, you may need to replace the control board.
If you're not comfortable with the above steps, it's best to contact a qualified repair technician for assistance.
1/31/2023 5:25:24 PM •
Exercise &...
•
Answered
on Jan 31, 2023
•
46 views
Is an E8 error on Ancheer treadmill fixable?
Whether an E8 error on an Ancheer treadmill can be fixed depends on its underlying cause. Possible causes like a broken control board, loose wires, or a damaged motor can sometimes be resolved with proper repair or component replacement. It's best to seek assistance from the manufacturer or a professional repair technician for proper diagnosis and resolution.
1/29/2023 7:06:38 PM •
Exercise &...
•
Answered
on Jan 29, 2023
•
587 views
What is error code 53? Treadmill only working when incline is 0.5. When change up or down, it shuts down.
Error code 53 typically indicates a problem with the incline motor or the incline sensor on a treadmill. It could be caused by a malfunctioning incline motor or a problem with the wiring or connections between the motor and the sensor. The fact that the treadmill only works when the incline is set to 0.5 suggests that there is an issue with the incline mechanism and it may need to be serviced or repaired by a professional.
1/18/2023 10:56:42 AM •
Exercise &...
•
Answered
on Jan 18, 2023
•
88 views
Nordicktrack elliptical NTEL79820 - internal tablet does not see the pedals movement
- Ensure that your pedals and tablet are properly paired and connected to the same WiFi network.
- Make sure that your tablet's Bluetooth is turned on and that it is in range of the pedals.
- Check for any software updates for both the tablet and the pedals, and make sure that they are running the latest version.
- Try using a different cable to connect the pedals to the tablet, in case the current cable is damaged.
- If none of these suggestions work, you may want to contact the manufacturer of the pedals or tablet for further assistance.
1/18/2023 10:54:50 AM •
Exercise &...
•
Answered
on Jan 18, 2023
•
32 views
TR2 speed button not working
It sounds like there may be an issue with the motor or the belt that connects the motor to the treadmill. I recommend checking the belt for any signs of wear or damage, and if necessary, replacing it. If the belt is in good condition, then the motor may need to be serviced or replaced.
1/17/2023 3:13:21 PM •
Exercise &...
•
Answered
on Jan 17, 2023
•
29 views
Not finding what you are looking for?