Vizio E500i-B1 50-Inch 1080p Smart LED HDTV - Answered Questions & Fixed issues

This kind of problem is not fixable, you need a new LCD panel.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary. Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ Line faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Faults to all LCD & Plasma screen are similar, irrespective of its brand and screen size.

bad panel

Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

http://www.shopjimmy.com/vizio-317gaawf047lon-wi-fi-module.htm

Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electro-medical.blogspot.com/

I would verify the voltages on the power supply board first because an improper voltage to a circuit board may make that board look bad.

Check Connections: Ensure that all cables connecting your TV to external devices (such as your cable box or gaming console) are securely plugged in. Loose connections can cause display anomalies. Test Different Devices or Apps: Try using other devices or apps with your TV to see if the issue persists. If the TV's menu looks fine but a specific device is causing trouble, that device might be the culprit. Adjust Picture Settings: Navigate to the picture settings by pressing the 'Menu' button on your remote. Experiment with different picture modes. Sometimes a minor adjustment can resolve display problems. Soft Power Cycle: Unplug your TV from the power source. Press and hold the power button on the TV for about 3-5 seconds (this helps drain any residual power). Plug the TV back in and turn it on. Some TVs also have a 'Soft Power Cycle' option in their settings menu, so check there too. As you have tried a reset, that takes us to the options of contacting Vizio support and/or your warranty.

The power supply/subwoofer for the VIZIO CA-27 series all-in-one PCs is identified by the part number 715G6960-P02-001-002S or ADTVE1825AC71. The power supply connects to the motherboard via a proprietary dual jack Audio/Power cable. I couldn't find specific voltage details for the subwoofer/power supply in the available resources. For precise information, I recommend checking the user manual or contacting VIZIO customer support directly.

No model number so generic advice only. Google 'vizio (model) manual'. ..

It is a very standard non-smart television. It is 14 years and 4 days old according to the manual. 26 Jan 2010 was its birthday. https://www.google.com/search?q=Vizio+M220MV No casting because there is no way to connect https://www.google.com/search?q=Vizio+M220MV+connect+to+tablet Manual https://www.manualslib.com/manual/187638/Vizio-M190mv.html#product-M220MV ..

RC: Living Solutions (or Innovage) jumbo universal ...

Remote Central https://www.remotecentral.com > rc-remote > thread Jun 10, 2007 - Hold the device button you want to program for 3 seconds & release. Push & release the power button & the red light will remain lit. Push the ... Living Solutions Jumbo remote need codes - RC 5 posts Jan 18, 2008 RC: Living Solutions Jumbo URC - Remote Central 6 posts Jun 20, 2011 More results from www.remotecentral.com

Remote Codes / Universal Remote

Vizio https://support.vizio.com > article > Remote-Codes-Un... Remote Codes / Universal Remote ; 2 Digit TV Remote Codes 19 ; 3 Digit TV Remote Codes 502 627 004 113 505 011 ; 4 Digit TV Remote Codes 1758 0178 1756 0128 0117 Missing: Living ‎ solution

How to Program a Living Solutions Universal Remote

Techwalla https://www.techwalla.com > Tech Support > How To Point the remote at the device you are programming and press the corresponding device button on the remote. These buttons are labeled "TV," "VCR", "DVD," etc.

Reboot the Router. Power cycle it and the television for 5 minutes by removing the wall plugs.

USER MANUAL - Model: E500i-A1

Vizio https://cdn.vizio.com > manuals > e500ia1_2ma... PDF It can be connected to your home network with a Wired or Wireless connection. Connecting to a Wired Network (Best). 1. Connect an Ethernet cable to your router ... 66 pages ..

The one logo is coming from the set top box that is supplying the signal, cable box, satellite box, Android box etc. Look for Mute on that remote, or cut the power to all your devices by removing the wall plugs. Wait 15 minutes and plug back in. ..

Bad LED strip lights, bad capacitors or bad diodes.

Press the INPUT button on the remote control to select a different input source. If you are using cable TV, satellite, or antenna connected directly to the TV, scan for channels See page 51 of user manual. UM_E601iA3E.pdf (vizio.com)