Top 20 Janome Memory Craft MC300E Embroidery-Only Machine By The Each Questions & Answers


sadly I can not but try it either way and see if it works properly , if not reverse

Janome Memory... | 44 views | 0 helpful votes


Hello pat this is a function of the hoop size. if the hoop is tall but not wide you cannot flip it. choose a larger hoop

Janome Memory... | 54 views | 0 helpful votes


Hello I have a Combi dX 502 model so I will send you a photo and I wonder if you buy them back Thank you for replying

https://translate.google.com

No, FIXYA does not buy or sell sewing machines.

Janome Sewing... | 24 views | 0 helpful votes


Sounds like your tension is too tight for one, and the timing is off . That's why you hear a click. The gears aren't in sync.

Janome Sewing... | 21 views | 0 helpful votes


In the bottom of the machine is where the reverse mechanism is. There is a cam that slides on a shaft to reverse it. Sometime the cam get stuck, try using some WD40 to clean it and the lubricate with sewing machine oil if it frees up.

Good Luck

Janome Sewing... | 36 views | 0 helpful votes


Hi there, If the length from the bottom of the presser foot to the center of the screw is half an inch, you have a low shank machine. If you measure 1 inch or longer, you have a high shank machine. Hope this helps, have a great day!

Janome Sewing... | 25 views | 0 helpful votes


Hi Eleanor, that issue is almost always the thread itself causing it but here are a bunch of things to try. ONE AT A TIME...so you'll know immediately how to fix it next time.
1. Try a different spool of thread.
2. Turn the spool around so the thread comes off the spool on the opposite end.
3. Change your needle and make sure you are using the right needle for the thread and the job. (I'm notorious for skipping that step, and I pay for it every time...when I grow up, I want to remember stuff!)
4. Check your tension...too tight may cause it.
5. Make sure there are no burrs around the hole in the foot plate. If a burr catches a bit of the thread, it can catch one of the plies of the thread and pull only that one, that will make it twist up on itself further back
6. Check the tensions discs for burrs and debris. I take mine off and clean them with alcohol and then put a dab of clear machine oil on them, then wipe that off so it's not dripping. Don't take yours off if you are not comfortable with doing it. If you loosen the tension, you can wrap a tooth pick with a piece of scrap, put some alcohol on the scrap and move it around between the discs. Another (my fav) option is to use pipe cleaners with a bit of alcohol on them.

I hope something works, good luck!

Janome Sewing... | 24 views | 1 helpful votes


Try to reboot the machine. The damage might already be done. Turn machine off, remove usb. Turn back on. Was the design the proper format?

Janome Sewing... | 26 views | 0 helpful votes


The Janome 6019QC has the reverse stitch button to the right of the threading path below the thread tension dial. The thread tension dial is under the top cover but the two points help triangulate the button. The reverse stitch button is shown as item 27 on the first illustration of the parts of the sewing machine in the manual (page 2 of the manual, page 4 of the PDF). Janome has the manual on the retired machine page: https://www.janome.com/support/retired-machine-manuals/ . The manual is in the right-hand column under the Other Machines heading. The current link to the manual is https://www.janome.com/siteassets/support/manuals/retired/other-models/inst-book-6019qc.pdf .

I hope this helps.

Cindy Wells

Janome Sewing... | 49 views | 0 helpful votes


I searched the internet using https://www.google.comI only saw parts for that model number. Could it be named New Home in order to search or request manuals?I saw a youtube video for a different model showing a technician carefully opening a machine to repair a similar problem. It warns you to disconnect electric power before servicing.https://www.youtube.com/watch?v=xHcEJYDo12k

https://www.sewingmachinesplus.com/janome-manuals.php

Janome Sewing... | 28 views | 0 helpful votes


No the feed dogs aren't dropped on the Janome 1600 series sewing machines. Instead, you cover them with the darning plate. I haven't found the darning plate sold separately. https://www.sewingmachinesplus.com/jan-767-827-009.php is a source for the darning foot and darning plate. As far as I can tell, the darning plate is not among the original accessories for any of the Janome 1600 models. The manuals for two of the Janome 1600 models are on the retired machine page: https://www.janome.com/support/retired-machine-manuals/ . The manual for the Janome 1600P-QC is on that machine page: https://www.janome.com/machines/sewing/1600p-qc/ . The direct link to this manual is https://www.janome.com/siteassets/support/manuals/professional-series/inst-book-1600pqc.pdf .

I hope this helps.

Cindy Wells

Janome Sewing... | 17 views | 0 helpful votes


You tried disconnecting the stitch regulator?


No, try machine without regulator.


Yes, make sure you have power at the wall socket. Unplug sewing machine and plug in a lamp, radio, or vacuum to test for power. If power at wall socket, then plug sewing machine back in to wall socket. If still no power, disconnect and reconnect power cord at machine end. If still no power, try cycling the sewing machine ON/OFF switch a few times.


If still no power then likely the internal fuse or other.
https://www.manualslib.com/manual/1231564/Janome-1600p.html?page=16#manual

Janome Sewing... | 29 views | 0 helpful votes


Try taking the bobbin out and see if the machine will turn by hand movements using the flywheel or running the motor, you will feel and resistance if there is any but do not force the machine! if the machine turns without getting stuck then try a different bobbin as this might indicate a problem with the bobbin. I am also assuming you have placed the bobbin facing the correct way meaning the thread which is an easy mistake to make. Next, try eliminating different parts of the machine like turning it on different settings or without a needle, open the front part of the machine where you would normally replace the light bulb and watch as you hand turn the machine for any knocks or places of resistance, also unscrew the very backplate at the flywheel as the machine is usually connected by a rubber belt going from the motor to the machine and check that it is not caught up or broken. On older machines that did not have an onboard computer made it more easy to solve problems because if there is a problem the machine wouldn't just shut down, So elimination should solve the issues.

Janome Sewing... | 33 views | 0 helpful votes


SAD TO SAY CAN NOT SAY AS I HAVE THE OLD KIND THAT SAY NOTHING JUST SEW WHEN I WANT THEM TO

Janome Sewing... | 29 views | 0 helpful votes


PERHAPS AT A SHOP THAT SELLS JANOME MACHINES

Janome Sewing... | 27 views | 0 helpful votes

Not finding what you are looking for?
Janome Memory Craft MC300E Embroidery-Only Machine By The Each Logo

2 questions posted

Ask a Question

Usually answered in minutes!

Top Janome Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1134 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

220 Answers

Irene Tulloch

Level 2 Expert

491 Answers

Are you a Janome Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Janome Sewing Machines

  • Janome Sewing Machines

Most Popular Question

janome mc300e tell me correct direction

  • Sewing Machines
Loading...