Samsung HCL4715W 47" Rear Projection Television - Answered Questions & Fixed issues
Samsung projection tv convergence problem
I was just working on replacing my stk's and was wondering if you could tell me what value the resistors are? Here is my previous post if you would like to see it.
http://www.fixya.com/support/t191186-blue_out
I Have a Sumssung HCL4715W Tv timer flashes 40r 5 times and Tv turns off
A constantly blinking light means shutdown.The most common issue in this model is convergence-----if the convergence circuit has railed (this means shorted parts) it can cause the set to do what you describe.Before I suggest a course of action----what is your skill level with electronic repairs? Can you solder and or do a visual inspection?SD TECH
I got a Samsung HCL4715W from a neighbor and did
Hi , first thing is check for leaks coolant in all 3 tubes. It is a very common problem in Samsung projection TV. This means, if you have a leak, it makes no sense to repair your TV, isa big money for parts. Another possible solution would be convergence board is damaged, two STK 392-040 IC's number; also has associated resistors that can be opened or burned. Be careful, Try to open the TV and watch these two important details. If you have further questions, do not hesitate , I will be here.
Our samsung HCl4715W tv
The problem of your tv is the convergence. Projection tv set has a 3 colors red,blue and green this 3 colors must be properly lined up to look the video normal. When this 3 colors is not properly aligned the video will produce a double image of color or like a 3d or wavy. In order to fix this problem you should adjust it in the menu program of your tv you should move any of the colors to up or down, left or right if you cannot align the 3 colors the problem is the convergence ic it must be replace. To locate the convergence ic you should remove the back cover of your tv but be sure to unplug your tv, you will see this ic attached in a large aluminum plate it has a marking of stk--- and followed by a numbers. or you could contact a service technician do do it for you and save you from stress. Good day and best regards.
Samsung HDTV model HCL4715w1 has horizontal wavy
Yes,tv screen have R,G,B colors lines mis alingnments,have colors shaded pictures or 3D pictures look aike?Tv have a problems known as convergence pictures problems.The tv convergence board it is dead.This convergence board must require replacement of 2 STK convergence ICS and some or all of it resistors too.Fixed the tv convergence board to solved the tv convergence pictures problems.U have some mechanical skills like take things aparts and putting it back together again?Yes,try website like Tvrepairworld.com to buy a whole refurbish tv convergence board for the replacement.The DLP tvs brands names Samsung and Akai used the same tv convergence board.Or tries those tvs shops will cost u like $300-$350 for parts and labors.
Has vertical problems that comes and gos
Hi:
You need to have the solder connections on the vertical output IC. Also there is pump up capacitor that goes bad or leaky that need to be checked. Rework the entire vertical section of the set to make sure all solder connections are ok.
2 resistors are burnt rz126
Both of those resistors are 3.9 ohm 2watt metal film resistors for the convergence ICs. The ICs will most likely need replacement as well.
My tv messed up overnight.
this is likely a convergence problem, the convergence chips- stk-xxx-xxx would need replacement
along with the large wattage resistors connected to them-look for 1-3 ohms the exact value varies
over a number of models do an ohms check replace if out even a small amount
Blue image is ghosting and not lining up with
The tv have a problems known as a convergene problems,it dead.Tv have colors lines R,G,B mis alignments,have colors shadow pictures or 3D pictures look alike?The tv convergence board have dead 2 STK convergence ICS and some or all of it resistors too.These parts on the tv convergnce board,must be replaced to solved the tv picture convergence problems.Can u do basic things like take things aparts and install another things into it placed?Yes?Try website like Tvrepairworld.com to buy a whole refurbish convergence board for the replacement.The DLP tvs Samsung/Akai tvs used the same convergence board.Or the shop,will cost u like $300-350 for parts and labors.
I have a Samsung rear
Hi,
There could be many reasons for the same ranging from convergence problem to faulty hyper module. This problem needs a tech to properly diagnose the board and the module. It would be worth repair. Do not try to get it repaired from a local shop as i have seen them overcharging for small parts.The best option would be to call Samsung and get it replaced.The repair would be anywhere around $250 - $350 depending upon the fault.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
My Samsung HCL4715W will not turn on.....can it be
Your problem is do to shorted Convergence Ic's which will not let the set power up until problem is rectified. You have a very reliable set there. The Ic's will cost about $25.00 for the pair and a tech can install them reasonably cheap. I do recommend repairing it.
When I left on vacation
Hi,
This is an internal failure and needs repair. If you wish to repair it yourself, i need more details :-
1. Is there any sequence of red lights?
2. How old is the unit?
Let me know,so that we could proceed.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Not finding what you are looking for?