Samsung HT-P38 System - Answered Questions & Fixed issues

i thought the botton volume up was damage because still connected even you are not pushing it. or have you tried to clean the botton inside

Normally, that's exactly how you fix it but it may take more than a half an hour. Some devices take as long as 24 hours. If the unit doesn't reset itself after 24 hours, something is wrong and the the unit needs servicing.
That being said, your manual say that in case of a power outage to turn the unit off and hold the STOP (the little square) button on the unit for longer than five seconds. NOTE: Doing this will reset the unit and erase all saved settings.

try using a lens cleaner first which can be bought from your local multimedia store and run it a couple of times that shoud solve the problem if it still fails just message me

eBay $22

http://cgi.ebay.com/SAMSUNG-SONY-PROPRIETARY-SPEAKER-WIRE-CONNECTORS-4-2mm-/260660058130?pt=LH_DefaultDomain_0&hash=item3cb08cd812

$15

http://cgi.ebay.com/6-PIONEER-SAMSUNG-SONY-YAMAHA-HT-SPEAKER-CONNECTORS-15-/260750289541?pt=LH_DefaultDomain_0&hash=item3cb5edaa85]

Same problem with mine. I took it apart and noticed that the try doesn't aligned correctly with the reader after spinning. However, I don't know how to fix it. I am looking for a replacement unit that will work with the speaker system. Any ideas?

Check for fingerprints or dirt on your DVD. Wipe it clean and try again. Also check for scratches. Try another DVD and see if your system reads it.

My HT-P38spins to far - the DVDs will not line up correctly in the laser reader - sometimes they do but its getting rare - it rotates about 1/4" to far so the DVD binds and I get NO DISK error help ? 

Is their away to re align how far the platter spins ? 

You have to connect extra red & white audio cable from your TV's (or cable box, if you have one) AUDIO OUT to the Home Theater's AUX IN 2 at the back (below Video In). Set the HTS unit to AUX 2 using the AUX button on the remote control and you should be able to get sound.

Protect mode will kicking whenever a fault is detected.

Causes that can start protect mode are:

Electrostatic harges on internal circuits.
Leave the unit unplugged for power for one hour or so, this will allow discharge.

Bad speaker wiring.
Check speaker wiring, try unplugging and plugging back, or start after removing one speaker at the time.

Internal fault.
Internal fault is the natural cause for protect mode. If all the above did not work, then the problem is a blown component or an internal fault. In this case the unit must be taken apart , tested and repaired by an experienced person.
If the unit is less than one year old, or if you want to get service, call Sony at the phone number listed on the product documentation.

Regards.

you can go to bestbuy.com and at the bottom of page you can click on order parts and follow prompts to order original remote or you can call 1888bestbuy and ask for someone in parts dept. If not through bestbuy parts you can call 1800remotes. You need model number of system if you go through either company for original remote. I’m happy to help further over the phone at https://www.6ya.com/expert/brandon_60dfebff379d64bd

This definately means that you have a positve and negative speaker wire touching somewhere. First thing to do would be to check all connections at the speakers and on back of receiver and make sure all wires are seperated. This is a common problem if two wires are touching each other. If you check all connections and they look ok and you still have same problem you need to start unhooking all wires and hook them up one at a time and turn on system. If it works with one speaker then try hooking up a second speaker wire and so on until it gives you protection message again. Basically process of elemenation. Once you says that protection message you need to replace the last wire you hook up all together as you could of damaged it when running speaker wire or it could be a defect in speaker wire. I’m happy to help further over the phone at https://www.6ya.com/expert/brandon_60dfebff379d64bd

I had the same problem until I switched my player-to-TV connection from S-Video to Composite.  Then it worked just fine.  Now I have player-to-TV as Composite, and Wii-to-player as Composite connected to Aux1.

You have the mode selector for the surround sound on the wrong switch setting. Look at the owners manual to see what setting you need for synthensized suround. Go to http://www.samsung.com if you need an owners manual. You will find it with a little bit of searching. Good Luck

On the rear of your TV connect, with a phono/RCA cable to the Audio R + L sockets, connect the other ends to your Yamaha using the TV in sockets. See photos attached Hope that helps. HDMI is for video unless the extra pins are added for audio.

See service manual. There are no fuse in it. Service Manual: SA-WX900 ' PDF ' Loudspeaker ' Electronics (scribd.com)

See page no 65 troubleshooting in user manual YPU4J-CANADA-ENGLISH0.0_0610.indd (samsung.com)

See following link, it may resolve your issue My MP3 Player Is Locked Up (Frozen). ' Samsung Africa

Normally makers don't play ball between each other. Yes if it was a Samsung Television and a Samsung Receiver A/V System. Or if you have something like a Cable Box or Satellite System that is made to interact with other makes. Or if it is a Universal Remote. I think you were just lucky that it happened to use the same frequency. Look in the manual for a scan command. https://www.google.com/search?q=Connect+Samsung+OLED+S90+remote+to+Yamaha+RX-V361+via+optical ..

Check battery. It may require replacement.

Check the battery. It may require replacement.