Xerox 5830 Copier - Answered Questions & Fixed issues

Check-Replace CAN3 PWB

the problem is its dp unit

problem :
can't find the counter
solution :
Press the ‘Review” button on the Control Panel. The Review button is just below the Information “i” button. The “Total Copies” will be displayed on the bottom, left corner of the Touch Screen

if it is a 5830 model, go to the menu and look for tools.
type "1111" and hit enter
sometimes it can be "11111" and see if it works.
I hope this is the area you wish to enter.
If it is the auditron mode, place a Xerox service call for the service rep.

The machine has been sitting around for a while, or was just been stopped being used.
Try cleaning the brown roller in Tray 2.
Try the other paper trays see if they work. Tray 1 and tray 3.
We would need more information about the results of these areas and how it worked.
If there is alcohole, try cleaning the brown roller. The other rollers are harder to see. This machine could even have bad paper feed clutches.
A xerox serivce call would have to be placed to do the major repairs.

Hello sir; you have a bad copy cartridge, replace it !

Well, most of the copiers are having dept code features where u can set access code for the copier. But the setting is depends on the brand & model.

If you donot find paper in the machine check for a stuck actuator or a bad sensor.

2 things primarily.
1 is dirty optics. Remove the glass, and the black optics tub. clean all the mirrors the lens and the lamp and the surrounding area around the lamp.
2. The copy cartridge may need replaced.

If the backgroung remains pretty consistant, it is most likely the optics.
If the backgroung get worse as the machine runs, or is different every other page, the problem is the copy cartridge.

Try this reset.
Power the machine off, Hold "0" the zero key while powering the machine on. That will put it in diagnostics mode.
Then enter 20, press start, then enter 3 and start.
Power off and back on and let me know.

Dear sir; Thank you to bring out the question to refresh my memory, I hope is correct! the error code 06-43 or 40 that all belong to optical problem, my suggestion ;
1, remove the glass plateform
2, check the exposure lamp continuaty, if nocontinuaty replace it.
3, check the exposure thermos fuse continuaty,if no continuaty replace it.
GOOD LUCK, if you need more help let me know
HAVE A HAPPY HOLIDAY !!!

if its a u9-1 code it is the lamp that is faulty. Sometimes it can be the connections either end of the lamp but normally the lamp itself. It will probably cost as much to fix as it would to get a new one to be honest

If you've modified one of the trays and still encounter the same error, it's worth checking if there are any obstructions in the paper path or if the default paper type and color settings need adjustment. Remove Jammed Paper From Tray 1: First, remove any paper from the Bypass Tray. Grasp both sides of the Bypass Tray and pull it straight out of the printer. Next, pull out Tray 1 until it stops. To remove the tray, lift the front of it slightly, then pull it out of the printer. Check for any jammed paper and remove it. Also, make sure there's no crumpled paper left in the tray or jammed inside the printer. If you have Tray 2 (optional), check it as well. Insert Tray 1 back into the printer and push it all the way in. Fully insert the Bypass Tray as well. Confirm the paper settings if prompted. Try your job again. Power the Printer Off then On: Press the Power/Wake button on the printer control panel. Choose "Power Off" to turn off the printer. Wait for a few seconds, then press the Power/Wake button again to turn it back on. Retry your print job. Replace the Paper Feed Roller (if needed): If the issue persists, consider replacing the paper feed roller. Refer to your printer's documentation for instructions on how to do this. If the problem continues, contact Xerox support.

Question edited for clarity. I found this 123-315 UI Panel Communication Error N 2.2. There is help in the first link but you need to register https://www.google.com/search?q=xerox+6204+error+123-315 ..

That means there is no communication. There is a system error that is probably a fatal error. You could try updating the firmware.

Here is Xerox error code chart. Fault Code Information (xerox.com) See troubleshooting section of manual at page 148 Xerox® PrimeLink™ C9065/C9070 Printer All other relevant documents are here Documentation - PrimeLink C9065/C9070 Printer - Xerox

I would ask a friendly Xerox engineer for an OEM one.

Fault Code 062-395: Scanner Power Cable Connection Fault or power supply fault.

Error Codes and Support Web page above states: Error Description: Drive Logic Fail Solution: 1.Recycle your printer 2.Check all connections to the Engine Control Board 3.Make sure the correct firmware is installed. 4.If the error continues replace, the Engine Control Board (MCU PWB) Manual for free download at link below: Fuji Xerox Color 550 Administrator Manual Page 205

Try disabling it. 4112 / D95 families - Fault Code 077-313 : Multi-Feed Sensing Problems. First ... You have the choice to disable the Multi Feed Sensing feature on the machine if you fail to repair the problem or if you have a hard time sourcing the sensor or the board. The NVM Setting code is: 742-268.

4112 / D95 families - Fault Code 077-313 - The Parts Drop

The Parts Drop https://www.partsdrop.com > index.php > 4112-4127-d9...

Fault Code 077-313: Oversize High Capacity Feeder Fault

Xerox https://www.support.xerox.com > en-us > article Sep 21, 2015 - Fault Code 077-313: Oversize High Capacity Feeder Fault · Try these solutions · Did this help?

Error Code Xerox 4112 Error 077-313

Copytechnet https://www.copytechnet.com > ... > Xerox Sep 6, 2019 - Cause: Multi Sheet Check Sensor Actuator loose due to torsion spring disconnected from the arm. Due to improper removal of paper jam at Registration Roll. Jamming Error 077-313 and error 075 - 211 Nov 30, 2016 Xerox 4127 cp error 077-313 Sep 24, 2016 Error Code xerox 700 077-311 Jan 11, 2021 More results from www.copytechnet.com