20 Most Recent TDK DA-3826 2-Disc CD Recorder - Page 8 Questions & Answers

With some of the TDK NX models the 9 pin lead between the subwoofer unit and the control unit gets damaged in careless connection. Its not the most idiot proof connection out there and when the connector is not aligned rotationally with the socket and/or pushed in at an angle, the connection pins can get bent. Sometimes if there arent too many pins bent, the pins can be carefully straightened and when properly inserted, the unit will work perfectly. In most cases however, one, or maybe even two fuses in the subwoofer unit will blow. If the unit doesnt work in your case after correcting the lead issue, open up the subwoofer unit by removing the screws around the outer edge of the back panel of the subwoofer (about 10 screws) and carefully prize the panel away from the subwoofer box. Sometimes this may be difficult as the back panel is glued to the subwoofer box to varying degrees. Dont pull the panel away from the box too far as it is connected internally by leads, etc. You should find the two fuses on the circuit boards attached the the inside of the back panel, one for the input transformer and one for the amplifier circuitry. Replace them (**** Smith or Tandy electronics stocks them) and you should be in business. If it still doesnt work, there may be some additional damaged caused, but this is rare. If you need a new lead, Imation (TDK) will supply you one at a cost. Hopefully you can get it up and running as it is a great little HiFi.

TRY BLOWIN IT OUT

The memory stick is too large - use 1 GB or smaller

Are you try to download directly to a computer or directly to a mp3 player discribe more detailedly to your probelm

If the display is working, you have audio. Check your amplifier. 1300Watt adaptor ... This unit draws a very low power and that is not needed.

1. Power Off: Turn off the device.
2. Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
3. Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
4. Power Off Again: Turn off the device once more.
5. Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
6. Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.

If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.

this model SA rather than SC seems to be a Middle East model. The SC version doesn't have DAB. https://www.google.com/search?q=panasonic+sa-pm250+instruction+manual ..

All questions need clear 'make model (what it is)' first 3 words. https://www.google.com/search?q=fmdott085+V398 ..

Question edited for clarity, typo and CAPS. Question moved from Cars and Trucks category. Claim on the warranty irrespective of how long you have had them. They charge $180 but they cost them $20 to buy from China. Package them up and send them tracked and ask them to replace the batteries. How long is the warranty on AfterShokz? While we hope you never need it, all new Shokz purchased from authorized retailers come with a two-year warranty that begins on your date of purchase. Jan 11, 2019

How To File A Warranty Claim For Your SHOKZ Headphones

https://www.google.com/search?q=Openfit+Shokz+battery+replacement ..

Are you using the charging cables that came with it? That is a type C. Are you securely attaching the charging cable? A loose connection would keep the battery from charging. If you had a low battery, you would see a red light. That you have no light at all suggests there is no charge left in the battery. I'm not sure the reset will work with no charge which is why you ought to check the cables first. But turn it off and then hold down the Multifunction button for 10 seconds to reset it. Then turn it back on and see what happens. If you can, test the charging cable on aother device. If you have another type C charging cable, try it, just to eliminate a bad cable. If these suggestions don't work, you may try the manufacturer's customer support.

The F2100 remote is not explicitly listed as compatible with the AerialBox T2100, I recommend using the remote that came with your AerialBox T2100 for optimal functionality. If you have any specific compatibility concerns, I suggest reaching out to Dish TV customer support for further assistance.

I have the same model with the 8 track player, original manual, and original receipt dated 1975.

Probably nowhere as this is an Amazon / eBay special so made in China. You should be able to go to Windows Settings, - Hardware and tell Winderz to find a compatible driver. https://www.google.com/search?q=VIBE+SOUND+USB+Turntable+Model+VS-2001-USBT+drivers ..

Hi I have a manual (and an IQ Voice organizer that I'm trying to sell). I would happily send you a pdf file of the manual if you contact me. Robert

Set Time Hours and Minutes: Press Time/12/24 and Alarm1/ON/OFF buttons at the same time for two seconds and it will start to blink the hour. Press and hold the button for a fast setting or tap it briefly to increase the setting by one hour. Now set the minutes with time (press and hold) and min. How do I set the Audiosonic clock? Set current time Press and hold the time button and simultaneously press the hour to set the hours in 24-hour mode .

Questions edited for clarity, full 'make model (what it is)'.Spray the buttons with Electrical Switch Cleaning Fluid Spray. It is an old unit and the contacts are probably dry.https://www.google.com/search?q=CR-06PL..

Question edited for full 'make model (what it is)'. Unfortunately only this one https://www.mikesmanuals.com/Manuals_Details_3257.htm https://www.google.com/search?q=technics+sa-r430+manual ..

Blackweb is a Walmart brand made in China at the lowest price point. When they fail, you return them to Walmart for warranty replacement and explain you can't find the receipt. The will give you a store credit. Or you just buy a new one. There are some ideas here https://www.google.com/search?q=Blackweb+BWA15HO1O+but+get+no+sound ..