20 Most Recent Toshiba 32A33 32" TV - Page 9 Questions & Answers

Check link it may help:
www.remotecodelist.com/

First you need the remote. If you do not got it then www.remotes.com should have one fore you or you can purchse a universal.

2. you press menu on the remote and then auto program.

I hope this does help please do leave positve feedback and ratings for your free answer today. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Have you looked to see if the Button on the tv itself is stuck in. Press it and you might be able to feel for it sticking. If this is the case you may want to try a baby wipe or something similar to try and sort this out. (dont use a sopping wet cloth)

hope you get this sorted.

Little Dish Fitter.

Unplugged it for an hour.... buttons changed.....Unplugged it for four hours and everything worked......Left it plugged in overnight and back to original problem....

You may lose some channels when you retune the TV as the channels have been rearranged. To locate them look at the EPG although you may still find that some channels are no longer available on FREEVIEW. See the following link for additional information

http://www.freeview.co.uk/_retuneinfo/

If the above process does not work then check the link above for additional information and also visit the accompanying site links below to find more information for your model of TV / FREEVIEW box.

For troubleshooting the retune procedure visit http://tvretune.co.uk/troubleshooting/

For specific model information visit http://tvretune.co.uk/productmanuals/

problem sounds like closed caption settings. change CC to "off" or "cc1" . it is probly set to text.

You have an old tv so the best problems are bad capacitors and bad grounds. Have someone pull the board and search for high voltage caps [160volts or 250 volts] with 1 to 4.7 microfarads. Should be two or maybe three and check all grounds. If the 4 amp fuse is good than the above will save your TV.

if the brightness control has no effect, then picture tube is going out if it has a glass tube crt display. used to be a rejuvinator would cook off some of the deposit internally on the crt, but it also reduces the life of the set.

volt's must be checked on crt board
r b g outputs compared
if voltage's are good then gun is suspect
bad pix tube

Try to have the TV unplugged over night. If that does not solve it you may have to have the TV power supply circuit inspected for leaking capacitors, loose solders or may be a bad IC.

turn off your closed caption

change tact switches
you have windex syndrom
using too much windex cleaning tube

Flashing lights on most TV's indicates a faulty voltage somewhere in the power supply or other voltage sensitive section. Like the "check engine" light on most cars, repair will require a trip to the shop. Get an estimate first. In the new world of disposable electronics the cost of repair may exceed the value of the set.

its not your tv. its the program you are watching some show hd picture that fully fit your tv. some still dont have the format for widescreen flat panel tvs. its still

You need to degauss the CRT, there is a built in degaussing coil but its needs more power . this is simply magnetizm that needs to be removed . see if you can before a coil somewhere.gd lk
Eric I’m happy to help further over the phone at https://www.6ya.com/expert/eric_ab7c09ec01841771

The main power fuse inside the TV may have blown. The rear cover must be removed to check it. Unplugging the power cord from the wall outlet is the first safety item. Finding all the right screws to remove the cover (without taking out some you shouldn't) is sometimes tricky. When you remove the cover the power cord will still be attached inside, so remove the cover carefully. There is a danger of touching residual high voltage near the picture tube. Carefully look for a fuse near where the power cord attaches to the circuit boards. Often the fuse will be obviously burned open (the small conductor inside the clear glass is melted or the glass is blackened). Replace only with a fuse of the same type and amp rating. Putting a higher amp rating fuse or slower acting fuse can have costly and possibly dangerous consequences. Be sure to plug the power cord in when you do your test with the new fuse. If you haven't done anything close to this before, you may want to refer this job to an expert.

It sounds like it has magnitized sometimes you can unplug it and it will demagnatize when you turn it back on, otherwise you need a demagnitizing coil .

one of the color guns has failed there are 3 RED BLUE GREEN So red and blue make brown theres how it becomes sepia in color

Check your setting in the audio menu, it sounds like the speakers are turned off, you will be able to reset the apeakers from that menu, if that does not do the trick unplug it for a few hours

with comcast red ok select switch 11256, 10154, 10156, 11265, 10060, 10650, 10845, 11156, 11356, 11656, 11704
with comcast grey ok select switch 0154, 0156, 0060