2002 C320 - Page 7 - Answered Questions & Fixed issues

Check the light bulbs first. If OK the check the connectors. It may come loose. If OK then only check the fuses.

have just heard you only need the last four (4) numbers.
but you must add 1212 to the numbers, if your first number is 3 add 1 to make 4, if the second number is 6 add 2 to make 8, third number add 1 again and so on

May hav issue w car security. Apartstore has xperiencd peopl that giv freehelp

IF YOU HEAR RAPID CLICKING...IT MIGHT BE A BATTERY OR ALTERNATOR PROBLEM.OTHERWISEIt might be a faulty starter.One of the symptoms of a bad starter is a single clicking noise when you turn the key or push the start button. ... Most likely, you'll need to get your starter repaired or replaced. If you can jumpstart your car, drive to your nearest repair shop to get the problem diagnosed.there are many other possibilities,if the above options are not helping:Click the link below:https://carrepairworld.blogspot.com/2021/06/why-car-wont-start-you-hear-clicking.htmlthis will help.Thanks.

From time to time the key gets out of place in the bypass module. You'll need to open the bypass box and make sure the key is properly held in place so that the signal is transmitted properly. You may also have a hood pin switch that is not working properly, it must not ground when the hood is closed. There are other considerations. The neutral safety switch also can prevent the auto-start from working, it's just a matter of checking all of your leads and verifying that the component they are connected to are working properly. Your manual for the remote start system should include a troubleshooting guide, one may also be available from Viper.

Note: All transmitter codes must be learned at time of programming!! The RS900 learns up to 4 different transmitter codes. 1. Open Hood (If no hood pin installed with your system, then you must ground the Gray Hood pin wire). 2. Turn key to the ON position. 3. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 4. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a 2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd code and so on. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off and close hood. CRIMESTOPPER COOL START RS-900 OPERATING INSTRUCTIONS MANUAL Pdf Download ' ManualsLib

Contact Peak directly to inquire.

Moisture can cause issues as you describe.

https://www.fixya.com/support/t2184779-hunter_tire_machine_tc3250_bead_breaker

recent worldwide changes in radar technology means that detector technology is not always capable at detecting these mobile cameras, The only way to keep up to date with the newer technology is to constantly keep updating your radar detector. The only issue is they only have to make small changes to the cameras and the new technology won't work.

as with any detector when it goes off they already gotcha

It is best to find an experienced veteran to replace the Mercedes alternator

I don't have the same jump box but I have ran into the same problem is either gets charged in the garage or in the house that's best result for me anyway

Jump starters with a lead acid battery are very similar to each other and many are generic label engineered imported items. The manual mostly covers the safe useage and operating procedures that are mostly intuitive - few people that know nothing about inflating tyres or jump starting a dead vehicle would own a jump starter... Jump starters are mostly so similar the instruction booklet for one will serve for many others. There is really only a few things to remember - a battery can explode so if sparks have to be made make sure they are nowhere near the (vehicle) battery, observe the correct polarity (failure to do so can be very expensive) and top up charge your jump starter after each use and monthly regardless (leaving it in a discharged or semi-discharged state will quickly render it useless).

This link will allow you to download the instruction manual you want in a pdf format.

you can purchase from: https://www.amazon.com/Adapter-Charger

https://help.compustar.com/s/article/How-Do-I-Exit-and-or-Enter-Valet-Mode

You can see this link.

http://codes.rennacs.com/Petrol-Engine/Japanese-Korean/Nissan-Engines.php http://www.nissanforums.com/stanza/141416-data-link-connector-location.html see abpve links for possible assisstance

Suggest to do a patent search and review some diagrams. That will get you started.

Try this page for a manual.... http://amzsalesuniversity.com/forums/topic/micronta-metal-detector-63-3003-manual/ Regards Geoff