20 Most Recent
Sharp AR-M205 Copier - Page 9 Questions & Answers
What is the error U2 ?
U2 04
Content: EEPROM read/write error (Serial communication error)
Detail: EEPROM access process error
Cause: EEPROM abnormality
Check and remedy: Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.
SHARP AR-M205 DRIVER HOW DOWNLOWD ?
Click
HERE to download the driver for your operating system.
Additional download site
HERE and enter AR-M205 on the data field.
You will need unzipping software to unpack the driver then install it.
It will take a bit of software know how if you computer is not setup to unzip file automatically.
It will take administrator privilege to install this driver onto a secure network.
Before you make any attempt to install this driver please log into your operating system as administrator.
Flashing light on display H-4 what does this mean
H4 = Low Heat Roller Temperature Detection.
Possible causes:
Thermistor abnormality
Heater lamp abnormality
Thermostat abnormality
Control PWB abnormality
Try resetting the error code using the following sequence....
Press #,Interrupt,C,Interrupt Then press 14, Start Button.
Hopefully the machine should now come to ready. If not check the heater unit for paper jams that could be blocking the thermistor or thermostat. The thermostat may have a small button on the back, try pressing this in. (it pops out if it detects overheat).
Otherwise it's likely to be the Heat Lamp that requires replacing.
Hope this helps
Sharp m205 error u2 Problem, what does mean?
press 0
U2 if 04 occurs EEPROM read/write error (serial communicationerror)
if 11 occurs Counter check sum error (EEPROM)
if 12 occurs Adjustment value check sum error (EEPROM)
if 40 occurs CRUM chip communication error
Blinking U Blinking 2 in Display
When you press the copy key , it should show 40 and this is the solution. Remove the TD cartridge and unscrew the toner sensor and wipe with a small blower. Clean with a brush if the toner particle is stubborn and blow. Then screw back and clear with key press #*C* and enter16 then press copy key. If it re-appears, replace TD cartridge with Sharp AR-202ft. Enjoy the job.
ARM205 Error Code CH. what
If CH flashing reinstall your toner cartridge properly if not that mean you have an open door close it.
How do you tell how many copies have been made
Hi, there are two ways of taking meter reading.
- Simply press and hold 0 key till you see six digits and write them down. For example 000,654 means that it has copied 654 copies since you bought it .If you hold # key as above, you will see the number printed if you use a printer. The difference between the two is the printed copies.
- The other is the command mode where you press command 22 enter 05 enter and read the copies.
Error Code E7-11 on a
This code is related to laser unit functioning problem. Power the machine off and on and if it appears again, do the following;
- Open document glass and clean inside mirrors and document glass with a clean dry soft cloth and test.
- Check flat cable that connects copy lamp and attach firmly from the main board.
- Replace the laser unit if the above fails.
Ask for assistance if you doubt from a qualified technician and you will succeed.
SCAN ERROR E7 11
E7 -11 : mean shading trouble (white correction )
clean the mirror,the lens and the reference white plate
Code e7-10
Check flat cable installation to the CCD
unit.
Check CCD unit
What is an H4 code and what do I need to fix it
H4 mean fusing lamp problem so you have to
1) check the fusing lamp
2: check fusing lamp thermostat
and after all you must rest the code by press - # key -interrupt key - C key - interrupt key - 14 - ready
How to see paper count
Hi, i suppose you mean the copier meter reading. There are two ways one is for the copies made and the other for prints made. Press and hold # for reading prints made and press and hold 0 for copies made. Read the six digits that appears and record on a sheet of paper as they start and thats the reading. To know daily readings, subtract the figure for evening from the one for morning and the difference is your reading.
What is error code L6?
If I remember correctly, the error code means that your laser is not working correctly. When the copier is "ON" will it make a load humming noise? You will most likely have to replace the laser polygon mirror motor. It is not that hard to replace and you can buy it on line.... Basicly how much do you like the copier? It may not pay to repair it. I would look up the part price..... Good Luck
Problem code L 6?
Hi, this is the problem with polygon motor defective. Follow this procedure to replace it;
- Open front cover and remove the screws securing the cover where paper falls after being copied.
- Make sure to turn off the power switch and remove the connector on the laser unit.
- Unscrew the screws on the black laser unit and remove it out.
- Carefully remove the locks on the black unit and remove it out.
- You will see a small shining polygon motor and remove it out.
- Replace a new one making sure your hands are clean not to make it dirty.
- Undo the reverse of how you removed it ending with connecting the connector.
- Power on the machine and the code should go away and return the cover and you are done.
Driver for installation in win 2000
Drivers for Sharp AR-M205 are available at Sharp Official Support site Click
here and make selection as under: -
Select
ARM205 > Windows 2000Hope this helps! Dont forget to rate the solution!!
CreativeTECH
Not finding what you are looking for?