Posibllities to eliminate: 1) bad door seal 2) unbalanced fridge on floor 3) buildup of ice in fridge (defrost) 4) faulty door alarm.
Check temp of fridge. Adjust up or down depending on whether too hot or too cold. Check for blocked air flow or too many items in freezer. But if the exterior is much warmer than usual, you may be looking for a repairman. The main circuit board might be blown
Try a reset by unplugging it for 5 minutes, then plugging it back in. If a minor problem, this may stop the beeping.
Maybe worth a look through this catalogue but I doubt spares are available;
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&ved=2ahUKEwjizJ7-k92DAxWzQkEAHUqwDmQ4ChAWegQIBxAB&url=https%3A%2F%2Fwww.specialized.net%2Fmedia%2Fwysiwyg%2FSpecialized%2Fetc%2FSpring-2023-catalog.pdf&usg=AOvVaw2Z06h4GZtS13wC9OK0rLZl&opi=89978449
Here is the manual link
Press CTRL+F Type in 'tax' top right, press Enter. Scroll through the 19 mentions, Number 3 shows it. Copied and pasted below, but it doesn't show symbol image. The first paragraph covers getting into setting mode and setting date and time, then comes 'Tax Rate'.
https://www.manuallib.com/download//SHARP-EL-1801PIII-OPERATION-MANUAL.PDF
GT • RATE SET GRAND TOTAL / RATE SETTING MODE SELECTOR: "GT": Grand Total "•": Neutral "RATE SET": To set the date, time, and tax rate, set this switch at the "RATE SET" position. Date: • Enter in the order of month, day and year, then press to complete the entry. • Use to separate month, day, and year. • When is pressed, the number entered is evaluated and displayed as "date" if the value is within the following range; "Error" is displayed otherwise, and the previously set date is restored. Month: 1 - 12; day: 1 - 31; Year: 2000 - 2099 (in 4 digits) or 00 - 99 (in 2 digits) Time: • Enter in the order of hour, minutes, then press to complete the entry. (There is no entry available for the seconds value. The clock starts at zero second.) • If the hour/minute digit is less than 10, it is not necessary to enter the first digit "0". • Use to separate hour and minute values. • When is pressed, the number entered is evaluated and displayed as "time" if the value is within the following range; "Error" is displayed otherwise, and the previously set time is restored. Hour: 0 - 23 (24-hour system for the hour entry), Minute: 0 - 59
Tax rate: • Press three times, enter the tax rate, followed by . • A maximum of 4 digits can be stored (decimal point is not counted as a digit). • Only one rate can be stored. If you enter a new rate, the previous rate will be cleared.
more here and videos
https://www.google.com/search?q=sharp+el-1801piii+set+tax+rate
..
Go to the Sharp web site, find your device and load drivers, download the driver for your device ensuring it is compatible with your OS.
Follow the on screen instructions.
To resolve this issue, you can try updating the printer driver to the latest version. You can download the PCL 6 driver for Sharp AR-M420u from the following website :
https://oemdrivers.com/printer-sharp-ar-420u-driver
If updating the driver does not resolve the issue, it could be due to a drum motor lock. In that case, you may need to check the drum motor operation using SIM25-1 and ensure that the harness and connector between the PCU PWB and the drum motor are properly connected .
Sharp AR-M420U with L4-02 error (copytechnet.com)
Power Off: First, make sure the projector is powered off.
Control Panel: On the projector itself, locate the control panel with buttons. You should find buttons like "Menu," "Enter," "Up," "Down," "Left," and "Right."
Access Menu: Power on the projector and press the "Menu" button on the control panel. This should display the on-screen menu.
Navigate Menu: Use the arrow buttons (Up, Down, Left, Right) to navigate through the menu options until you find the "System" or "Settings" menu.
Unlock: Within the System or Settings menu, look for an option related to the system lock or security settings. Use the arrow buttons to select it.
Disable Lock: Once you've highlighted the lock option, press the "Enter" or "OK" button to access its settings. You may need to enter a password if it's set, so try default passwords like "0000" or "1234." If none work, you might need to contact Sharp support for a password reset procedure.
Unlock: After accessing the lock settings, disable or unlock the system lock.
Exit Menu: Exit the menu by pressing the "Menu" button again.
Test: Power off the projector and then power it back on to see if the system lock has been successfully removed.
You don't. According to the Sharp MX-3110N user manual, there is no Simulation 50-22 EXECUTE option available. You can try running a halftone calibration 44-27 followed by a full calibration 46-74. If that fails, you may have to consult a professional technician.
First portion of your problem seems to be caused by Printer Cartridge. Second portion seems the fault is in the scanner.
Refer to section 8 of Service Manual
Download Sharp AR-5618 Service Manual ' ManualsLib
The dotted triangle and blinking LED on your Sharp AR-7054 TV are indicators of a video problem. There are a few possible causes for this, including:
A loose or damaged HDMI cable.
A problem with the TV's internal video circuitry.
A problem with the source device (e.g., Blu-ray player, streaming box).
To troubleshoot the issue, you can try the following steps:
Check the HDMI cable connections between the TV and the source device. Make sure that the cables are properly inserted and that there are no visible signs of damage.
Try using a different HDMI cable.
If you are using a streaming device, try connecting it to a different HDMI port on the TV.
If you are still having problems, contact Sharp customer support for further assistance.
Here are some additional tips that may help you fix the dotted triangle problem on your Sharp AR-7054 TV:
Try resetting the TV to factory settings. This can be done by pressing the Menu button on the TV remote control and selecting Settings > System > Reset.
If you have recently updated the TV's firmware, try rolling back to the previous version. This can be done by downloading the previous firmware from Sharp's website and following the instructions in the firmware update file.
If the problem persists, the TV may need to be repaired. Contact Sharp customer support for assistance.