Top 20 Sunbeam 722 Auto Shut-Off Heating Pad Heater Questions & Answers

What the actual F???

Hi

As its new I would recommend you to get use warranty and get it repaired/replaced. However, if you still want to do this yourself then pull out the main wire box located inside the pad and then take it apart and use hair dryer to dry the electronic control board, this should work, however remember that opening it will void the warranty. Hope this helps...please post back for further assistance.

Daniel

Here's a discussion on the issue ::

http://www.fixya.com/support/t1520727-f2_fault_code_heating_pad


Charlie

This means that the controller for the heating pad has a short. Water will cause the controller to short out. If water is spilled on the controller you can unplug the cord and take the controller apart and use a hair dryer to dry the controller out. If no water has been spilled on the controller you can take it apart to make sure all of the wires are still soldered in place.

Unplug & then plug in... will help for a little while, but the F1 will return. Sorry.

My electric blanket had the same message and I could not find anywhere to answer question. Sunbeam said to look on th cord tag and this was no help. I finally pulled out the main wire box inside blanket and took apart to see if there was anything obvious. All solders looked fine but then I noticed a drop of water. Used a hair dryer to dry the electronic board, reassembled and it worked. Must have been a water short.

What control, brand, model # etc.? An educated guess would be that you have a gas forced air system. FF would typically mean Flame Failure. Pull flame sensor, clean rod with steel wool until shiny again and reinstall. Your flame sensor will have one wire going to it. Located at the opposite side from the igniter. It will have a ceramic base with stainless steel probe protruding into the flame. Hope my guess helps.

Sure, here are a few suggestions on where to find a replacement controller for your Sunbeam BL0750 electric blanket:

* **Sunbeam customer service:** You can contact Sunbeam customer service directly and they may be able to help you find a replacement controller. Their contact information is available on their website.
[Image of Sunbeam customer service website]
* **Online retailers:** There are a number of online retailers that sell replacement controllers for Sunbeam electric blankets. A quick search should turn up a few options.
* **Local hardware stores:** Some local hardware stores may also carry replacement controllers for Sunbeam electric blankets. It's worth checking with your local store to see if they have any in stock.

Once you've found a replacement controller, you can either install it yourself or have a professional do it for you. If you're not comfortable installing the controller yourself, you can take your blanket to a qualified electrician or repair shop.

Here are some additional tips for troubleshooting your Sunbeam BL0750 electric blanket:

* Check the power cord to make sure it's plugged in securely.
* Try using a different outlet.
* Check the fuse or circuit breaker to make sure it's not tripped.
* If you've tried all of these things and the blanket still doesn't work, you may need to replace the controller.

I hope this helps!

There is chance that arcing brushes in the motor are causing the odor. They should be replaced and the armature cleaned. A sunbeam repair shop can refurbish your mixer if the parts are still available.

compressor not working or low on freon

A partstore knows or chec online

heating element possible shorted out.

Try these: -Make sure the remote battery contacts are clean; -clean fully charged battery surfaces with a lead pencil eraser to remove oxide; -could be loose contacts or cold solder joint on remote control board, especially if dropped a lot. if not tech savvy probably better to recycle old unit and purchase a new one . good luck!

Generally means u have a bad connection at the wall or at the control module. Disconnect everywhere u can and reconnect

Possible free manual if this is the same model with wick information. http://www.milesstair.com/Sunbeam3602.pdf

Try unplugging the power cord from the wall socket and check that the connection to the blanket is good and not loose. Then plug back into the wall socket and switch on. If error still occurs then there may be a problem with the blanket.

Wires probably damaged inside. Be carefull, I had one cought on fire. Dont like this things ever since

http://www.electricblanketinstitute.com/blanket-or-comforter-on-top-of-electric-blanket.html

You posted this in the Heating and Cooling Section. try another area.

then controller is faulty replace