Top 20 LeapFrog Leapster Explorer Learning Game System (green) Questions & Answers

Plug it harder and it charges your datuers leapstergs.

go to settings

Hello,
there are three basic reasons why the leapster explorer won't bring out sound.
1. Defective speaker
The speaker of your leapster explorer maybe defective, this can make it not bring out any sound. Disassemble the leapster explorer, check the speaker part, test the speaker with a AA battery. If you hear any sound using the battery, then it means there is nothing wrong with the speaker.
2. Loose wire connection
Disassemble the leapster explorer, check the wires connecting the speaker to the board. Check for any wire cut, or loose connection which can cause the speaker not to bring out sound. . 3. Sound IC/Card/Board
If non of the above is the cause of the problem, then it means the leapster explorer is having a defective sound ic/board/card. There is an IC on the board of the leapster explorer which is responsible for sound. If this ic has a shot, there won't be any sound. If this be the cause, I think it's high time to took the leapster explorer to a repairman because this requires skill.
I hope the above is clear. If not, please let me know for further assistance.
Regards.

I had same problem, just fixed it by a little hack. The volume up switch is broken.
1. Remove accessory door on bottom. 2. Remove all screws on back. 3. Open back cover.
Looking at the exposed board, there are 2 volume switches (back to back). Directly next the switches are four contacts: the upper 2 are for volume down, the lower 2 are for volume up.
4. Place the battery pack on the board and hold it down. 5. Press the power button to turn on the unit. 6. Use a small wire to jump the volume up contacts multiple times to change the volume to maximum (or desired level). 7. (Optional) Remove the volume buttons and throw away the rubber cushions to prevent the volume from changing. 8. Replace everything back in place.

https://s7.leapfrog.com/is/content/LeapFrog/Site%20English%20Assets/Support/Download/Parents%20Guides/80-602000-LeapPad-Ultimate-Parent-Guide.pdf

uefwiagyrskef

That's what I've been asking.??

Enter 1111 and it will say oops wrong password then enter 419 backspace and get rid of the 9 and then 27 worked like a charm took forever to find one that worked and this one worked for me once in change the 4 digit code to something ez

All parents are like to reduce the work load of their children. And here is the best essay writing service to reduce the work load for writing essay. And this dissertation writing services always ensures the best quality content and uniqueness of content.

the pen wouldn't launch from app on the desktop or turn on manually for me either, You need to launch it through their website, it's a rollover button top right on the website page 'Launch Leapfrog Connect' the pen then auto turns itself on!

Try pressing the on/off button to turn it off. I had a same problem. I depressed the on/off button for ~6 second or so and the device turned off. When I turned on again, the LeapReader no longer had a white light and was recognized by my computer.

http://writings-centre.com/

During a normal shut down, the screen image on a LeapPad will reduce to a white dot, which will disappear in five to ten seconds. In rare circumstances, the white dot will not disappear and the LeapPad will not fully power down. If the LeapPad does not complete the shutdown process and the white dot remains on the screen for more than ten seconds, complete the shut down by pressing and holding the power button on the LeapPad for ten seconds. This will fully power the LeapPad down, and it will start up normally next time you power it on. For more information contact essay writing service reviews Essaypaperreviews com Best Writing Services Reviews online

Have the battery checked first as it may not be connected properly or may be no good and not accepting a charge IF you run the machine off the adaptor it probably will not be charging the battery so I suggest you plug in the adaptor and leave the machine off for a few hours to see if the battery will charge.

SolutionIf your Leapster system does not respond to the stylus pen, it needs to be calibrated. To calibrate your Leapster system:

1. Turn the unit on and wait for the sign-in screen to appear.
2. Hold down the Home, Hint, and B buttons simultaneously.
3. When the screen changes, press the A button.
4. Using the Stylus, touch the center of the targets.

my leap pad ultra is at that part of turning off wher their is only a dot of wite left on the screen.it is still doing that and it has been at least 2 hours since i played it. it wont turn on either now.i am a kid sorry if their are spelling errors

Sorry, but you can't.

Get a new Leapster

Take it to an electronics reapir shop and ask to have the connection re-soldered.

This happened to ours last night having used it for 3 months without issue. Did you find a solution?