20 Most Recent
Hitachi 50UX57B 50" Rear Projection Television - Page 2 Questions & Answers
Double vision
I have a 60SBX72B and the colors are all separated like triple vision. Is there a way that I could fix this
My picture isnt bright and is slightly blury, why?
It is an older set but when was the last time the 3 lens were cleaned? If a while that may be your problem.These sets were designed to have the lens cleaned once a year--there is also a mirror but unless very dusty or a smoker not usually an issue.Remove back cover with set unplugged---note the three large black round housings on top----clean the lens with a paper towel with glass cleaner sprayed on the towel.This is the light source for your picture and if dusty picture will be darker and duller looking.Let me know if questions.
I have what I think
When the tv is it totally black and white and the tv picture are good and clear wright?when the tv colors are fade in and out are clear up and when the tv picture it is in colors it is look good normal picture wright?Tv have no shadows of any kinds of colors when picture are good in colors wright?Yes,take ur hand make fist or take a wooden hamer bangs all around the tv bazel frame if the tv colors come back or tv stay in colors it is have good picture in colors.Tv it is still good just have components parts are cold soldering or CRT colors guns R,G,B just require resoldering works only.
My hitachi 50ux58b just turned offf by itself i
Hello,
It's the problem of overheating in the power supply board of the TV.on the power supply board of the TV there are few capacitors and IC.any of this ic is got short or may be weak.so due to this when you start the TV the current passes from electric outlet to the power supply board of TV.but when the current passes from that weak/faulty part at that time current gets stopped or slow and the board overheats and TV shuts off. this is a common problem faced by many other users too.the possible option to solve this issue is to check the power supply board by a meter and continuity tester and replace the faulty component on the board which is short due to which power supply board is getting overheated.its bit technical job but yes its not at all a costly repair to do or get it done by the technician. for required parts it can be easily available from local electronic hardware shop.
I hope this will help in solving the problem...
I have a hitachi ultravision
Hi,
This kind of symptoms indicated that the power supply gone to protection mode. There's one of the output voltages gone bad which trigger the symptoms. Let me know if your handy with electronics because there's a test point in the power supply board needed to test to determine which voltage supply gone bad.
Working in this kind of symptoms must know safety precaution working in the active voltages and have necessary tools and test instrument like the multimeter.
Status of the led light in the front panel will also help to narrow the test points.
Jdvillanueva
I have a hitachi 50FX18B
You have a bad solder connections on the vertical IC (integrated circuit). The vertical IC is a inline pin arrangement black IC on a metal heat sink of aluminum. This is the best description I can give you because I am limited on information on this model. The bad solder connections should be clearly seen. Solder the pins with rosin core solder and electronic soldering iron.
Top left hand corner is
I HAVE AN OLDER HITACHI 53" PROJECTION TV THAT IS BLURRY IN THE UPPER RIGHT AND LOWER LEFT CORNERS. IT LOOKS LIKE THE TEXT IS OVER LAPED WHEN PLAYING MY PS3. IT MAKES IT HARD TO READ. THERE IS NOT ANY PROBLEM WITH COLOR, JUST BLURRY. HOW CAN I FIX
Waves going up the screen.
Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com
Common Problem #1) Convergence has gone out
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
Common Symptoms include....
- Screen looks 3D
- Colors don't line up
- One or more colors can't be adjusted when using the convergence menu.
- Screen is bowed or warped.
- TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.
SOLUTION #1
For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Common Problem #2) CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
Picture of a set that needs the fluid changed.
TV set after fluid change
SOLUTION
You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Convergence will not adjust , and the TV takes too
Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com
Common Problem #1) Convergence has gone out
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
Common Symptoms include....
- Screen looks 3D
- Colors don't line up
- One or more colors can't be adjusted when using the convergence menu.
- Screen is bowed or warped.
- TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.
SOLUTION #1
For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Common Problem #2) CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
Picture of a set that needs the fluid changed.
TV set after fluid change
SOLUTION
You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Not finding what you are looking for?