20 Most Recent Casio FX-300MS Calculator - Page 8 Questions & Answers

That is correct: there is an error in your request. The range of the sine function spans the closed interval [-1, 1]. Thus the domain of the inverse sine function (the arc-sine) is the interval [-1,1]. However you are asking the calculator to calculate outside of the domain (7/2=3.5). If you are using the hyperbolic sine sinh, that is another matter.

3027.

Shift LN raises e (about 2.718) to a power. Try this:
1 . 0 5 9 5 ^ 2 . 5 =

^ is the key to the left of the log key, below the big cursor pad.

It's the shifted function of the x^-1 button, just below the SHIFT button, marked "x!".

Your calculator is set to degrees. To change to radians, press SHIFT MODe and select Rad.

The top-left black key, right below the gray SHIFT key is labeled . This is the key you are looking for.

Divide the numerator by the denominator.

--W/D--

97.54387

Hi,

You can download and print the instruction manual for Casio FX-300MS in PDF format by clicking this link.

Adobe PDF Reader is required to view this manual. Download Adobe Reader

Hope this helps. Kindly let me know if you have any difficulty in downloading the manual.

Thanks for using FixYa.

press 4 and 7 and press degress button press 2 and 0 again press degrees button now it is it dergees button is in the 6 row from down at second place

For common logs (logs in base 10) use the 10^x function : Press [SHIFT] [Log] to access it.
For natural logs, use the exponential function. Press [SHIFT][ln] to access it.

Your calculator can store values into nine variables,named A, B, C, D, E, F, X and Y. You can store a value into one of them by pressing [STO] [letter] (they are marked in red next to the corresponding buttons).
A to F are general purpose variables, X and Y are used for statistics functions and M has some special functions attached like directly adding or subtracting to/from the stored value via [M+] and [M-].

Your calculator is giving you the correct answer, telling you that 0.77 to the 22nd is about 3.1827 times ten to the minus 3, or 0.0031827 . By default, the calculator will switch to scientific notation if the magnitude of the number is less than 10 to the minus 2, or 0.01. You can put the switch at 10 to the minus 9 by repeatedly pressing the MODE key until you reach the screen showing "Fix Sci Norm" on the top line. Press 3 to select Norm, then press 2 to select Norm2.

The calculator can only show ten digits. The only way it can show a number with ten or more leading zeroes is to switch to scientific notation.

Hello,
Here is the link to the manual.

http://support.casio.com/manualfile.php?rgn=1&cid=004001013

Hope it helps.

Hi,

To calculate the power press 8 then shift follwing the ^ symbol and then choose power number which is 4 in your case,

Eg: To calculate 3X4 to the 3rd Power, your input should be

(3X4)^4 this would get you the desired result

Please revert me, if you need more assistance, i would be very glad to assist you more.
If you were satisfied with the solution please rate this sollution.

Thanks For using FixYa!
Vinod Kumar J

Decimal Point and Separator Symbols
You can use the display setup (Disp) screen to specify the symbols you want for the decimal point and 3-digit separator.
• To change the decimal point and separator symbol setting, press the MODE key a number of times until you reach the setup screen shown below.
Display the selection screen. (Disp) 1.
Press the number key ( 1 or 2) that corresponds to the setting you want to use.
1(Dot): Period decimal point, comma separator
2(Comma): Comma decimal point, period separator