Top 20 JVC HD-52Z575 52" Rear Projection HDTV-Ready Television Questions & Answers

The parts diagram for the JVC HD-52Z575 is available here: https://www.searspartsdirect.com/model-number/HD-52Z575/1758/0333200.html . The lamp is part TS-CL110UAA. I don't see a separate ballast. If you look at the parts list for the cabinet, a Service manual is available. I hope this helps. Cindy Wells

If you wish to get some details; visit the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

Check the audio selecting section. It may have changed from audio via hdmi.

You might want to check and see if that was the right lamp for that tv. You might have the wrong lamp

u need the real remote rm-18g hit menu till u get to lamp reset hit enter a screen will come up that says press ok to reset lamp timmer hit ok button than another screen will come up that says the lamp timmer was reset successfully

HelloYou have to download the service manual to your tV to get these details. Try to download it from internet. It will be an impossible link to get as free download. Most of the service manual sites will be paid one.

Thats usually an issue with the receiver power board.

andycjavier,

See my tip at

http://www.fixya.com/TipsAndTricks/thanks.aspx?thid=8580883

Thanks for using FixYa and for the great rating.\

hardrocko

I have the same blue shadow with reverse image on my JVC HD-52Z575 Did you see what the problem on yours finally was?

You must get your ON before make any settings on it. Please check the power line first ( fuse and cable). Use the volt meter to check voltage on your tv

Make sure you pick the right input for the right HDMI port,

The tv "LAMP" LED light indication flashing or ligting up?Yes,the tv projection lamp live are over.Tv require a new projection lamp.

Make sure the projector lenses are clean and also the interior of the screen.

If you found this helpful please leave a thumbs up..............

Really? Try reading the messages you've been sent.

I've pasted this from your premium support request:


Your TV will not accept an HDMI signal from the Roku box. In the TV specifications on page 104 of your user manual you will note this:

HDMI jack x 2
Note: The Digital-In terminal is not compatible with picture signals of a personal computer.

The Roku box is effectively a PC. It is receiving digital media via the internet and streaming it to your TV in the same way as a standard PC would.

The only way you will get this to work, is with a different type of cable. I would suggest component AV.


Hope this helps. Unfortunately, your purchase of incompatible equipment is beyond our control.

BSElectric.

The sound board is gone.... it's not worth it to repair. Just use the analog audio out from the TV to the external audio system. that's what I do on mine.

hello sorry know one got back to i've just download the user manual you can try this because you haven't got the right remote. go in the menu closed caption auto shut off and the xds id turn that off as well if this don't work feel free to get back to me and i will look at another solution hope it helps

regards
shaun

This unit has cooling fans and it sounds like they are either plugged or not working. When a ballest usually goes out it does not come on and then go out. It is the coming on part that is hard for the ballest to do when going out. Sounds like over heating problems and if it is the ballest it could be any were on a tv and in many different locations. I would type your model number in and replacement ballest for this model number and go from their. Thanks

Ballast Board? it is what Powers Lamp, or CK Lamp Fan if it stops running and is not Keeping Lamp Cool
set is designed to shut off to Protect lamp from being burted up, you could have either Bad Ballast Board or Defective Lamp Fan,there is a few test you can do to see which Part is Bad.

The solution is an easy fix. Ignore anyone telling you to take it to a service center or to replace the convergence driver. You need to access the service menu on your television by using your remote control:

DRIVE CONVERGENCE Adjustment (Using remote control)

•Use the inner RGB box pattern.

(1)Set the [SLEEP TIMER] key to 0 min.

(2)Press the [DISPLAY] key and the [VIDEO STATUS]key simultaneously.

(3)Press the [9] key to display the RGB box pattern.

(4)Select the R mode by pressing the [DISPLAY] key.

(5)Adjust the R mode to setting as same as G mode bypressing the [CH ]+ / [CH -] key.

(6)Select the B mode pressing by the [DISPLAY] key.

(7)Adjust the B mode to setting as same as G mode bypressing the [VOL] - / [VOL +] key.

(8)Check to see that the cross pattern is white. If thecross pattern is not white, readjust (5) to (6).

That's it, your color is now corrected. Yes, I know...your welcome.