Top 20 VeriFone (M19755014US1) Magnetic Card Reader Questions & Answers

if you have a seperate check reader for your terminal. start by unplugging the credit machine power source from side, then unplug all other devices from credit machine. clean the reader with canned air, never use liquid. plug in the devices and the power source last, this should fix the issue. if it does not you can

Make sure your connection is good and live, but yes, a setting got changed. Call your payment support center and get the directions and specifics for their receivers and your terminals. Normally they can walk you through it. Ours does.

Invalid Terminal key

Receipt Feeds,But Nothing IsPrinted On It Not using thermal paper. Ensure thermal paper is being used. Thermal paper loaded upside down. Ensure thermal paper is being fed from underneath the roll, as it will only print on one side of the paper.

What that means is that there was some sort of communication error in the machine. In my case, a credit card payment went through to the merchant services but not through my machine. The balances did not match. Call the customer service number on your machine and they will fix it within a minute!

Hi,You need password reset software to access the sysmode menu1,[email protected]

NO you need the software to clear the tamper and the battery is easy and or better to let a professional do it.bad RTC can be repaired. the machine is equipped with multiple sensors inside. if one of them goes bad, or the Battery is dead tampering or bad RTC will show this can be fix by replacing the sensor and or the battery if you need this to be done call me @ (775) 358-2922 hope this help : - )

A T7+ is a drop and load terminal. Simply open the lid, drop the paper roll in, feed about an inch of the paper out from the bottom of the roll, then close the lid.

If you are just reloading a NOS in your Nurit 8020 machine, even if your machine is secured you should be able to load it, make sure your com1 baud rate setting is the same, your 8020 is set to 115200 baud rate, and should set up your com1 at the same speed...hope this will help and if you still need more help you can call us at (775)358-2922 ask for Randy. Thanks

If the printer does not work properly:• Check battery status or terminal power connection. The printer will not print ifthere is an insufficient charge remaining in the battery to complete the printoperation. (For Vx610 terminals only.)• Check if the printer is out of paper and that the roll is properly installed. Openthe paper roll cover and install a new roll of printer paper or ensure that the rollis feeding from the bottom.• Verify that the printer roller and paper roll dust cover are properly installed.• If the problem persists, contact 775-358-2922 hope this help : - )

See the link below:http://www.youtube.com/watch?v=0Pw0lidkUuk&feature=youtu.beAlso if you disconnect internal bettery, you will remove digital signature.Good look.

Unfortunately there is no Tampering solutions other than sending them back out to an authorized manufacturer for them to reset the Tampering switches on the machine and reset or repair the software in the machine. These machines have a multitude of tamper switches that can be set off by a jolt to the system from being dropped or from power surges and such. Sensitive equipment that requires a gentle hand to keep them running nice and smooth

Nurit OSP Loader is the the program we use to remove the TAMPER error. Replacing the internal battery and reloading a fresh NOS (nurit operating system) will remove the error. Check our website at freshpoint.org or call us if you can at (775)358-2922 . It can be fixed, you don't need to replace it. thank you.hope this help : - )

bad RTC can be repaired. the machine is equipped with multiple sensors inside. if one of them goes bad, or the Battery is dead tampering or bad RTC will show this can be fix by replacing the sensor and or the battery if you need this to be done call me @ (775) 358-2922 hope this help : - )

These terminals are almost all Thermal printers on them. To get your printing fixed to something darker when you open the paper door, you want to take a very lightly damp cloth or paper towel, do NOT get wet and wipe off the thermal print head just below the little metal serrated edge that you tear the paper on. This will clear off the print head of any dust and debris that will hinder the printing. If your weary of using damp cloth just use the tip of your finger and it will remove most of the debris.

The most common error with these terminals is that they are connected improperly. Everyone plugs the power in first then the rest of the cables. Ensure that your cables are plugged into the proper ports first. The 10-Base-T port is for internet only, the Phone icon port is for phone line, the RS232 is not used unless otherwise stated, the Calculator looking port is for pin pads only. Once the cables are properly connected reboot the terminal by unplugging the power cable for roughly 10-15 seconds then plugging the power back in. Once it starts again it should be fine. If you are running on a multiline system for phone the terminal will not dial out unless you set the prefix to dial 9 first.

There is no ink in this machine. Try changing the paper. If that doesn't work, then you need to either a)replace the spring that holds the paper cover closed so that the paper is pressed tightly against the print head or b) replace the print head. You can also try using a rubber band to hold the paper cover closed more tightly. If the spring is the problem, a rubber band will do the same thing.

An RTC chip error on these terminals is unfortunately the same as "Tampered". They can only be repair by a certified outlet and it depends on the issue it usually costs minimum $100 to repair one for use again by these repair depots. There is no way to fix it yourself as when it is opened you will definitely get a "Tampered" message because of the sensors in the machine.

To make it useable we need to remove the tamper first. Nurit OSP Loader is the the program we use to remove the TAMPER error. Replacing the internal battery and reloading a fresh NOS (nurit operating system) will remove the error. Check our website at freshpoint.org or cal us if you can at (775)358-2922 . It can be fixed, you don't need to replace it. thank you. hope this help : - )

There is a lever on the right hand side of the paper roller. Press it. The paper cover will pop open. Put in the new paper roll, and shut the paper cover with just a little bit of paper sticking out. You're done.

Yes, it really is that easy.