Top 20 Jensen VM9424 Car Video Player Questions & Answers

Rca jacks either are lose or either one burnt out

The screen has a connection for each line on the display and the soldier on some of these connections has gone intermittent. When the unit becomes warm enough, the soldier expands and the connections become more consistent. If you're skilled, this can be repaired. If not, either replace the unit or take it to a reputable technician.

It connects to ground

Hello lumberjack623,
When the jensen starts acting this way, it is simply a power problem. The device is not receiving power from the main source. The battery is weak and need to be charged before the unit can turn on once again. The battery power is too low to turn the unit on.
Try to check the power source or the connection to the power source. It is not charging the players battery. You need to have the connection port replaced. Also the power connection needs be checked.
The battery is simply weak that is why it goes right off when it comes on.
Hope this was helpful to you. All the best Elect_Comp

Make sure the fan opening at the rear of the unit is not obstructed. It cannot cool itself is this opening id blocked.

you have to turn off the gps time there is a setting in the menu that you turn off navigation sync or something like that. Go to setup and nav time. It is whatever setting has to do with navigation time

Hi,

How old is the unit?

As soon as you turn it on you get nothing but a white screen and no matter what you do it has a white screen correct?

Let me know,so that we could proceed.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Hi there,

In theory, the unit should retain the last setting/screen which was used prior to turning off the ignition (the instruction manual does not indicate otherwise). The Nav audio should also default when when in NAV function (the radio audio should not occur, unless there is an option to do this in the NAV menu setup).

First, try pressing the RESET button on the top/left corner.

Q. After turning off the ignition and turning back on, does the radio lose it's "presets" (ie radio stations you have programmed)? If yes, then the YELLOW wire is not connected to constant 12v power.

On the wiring loom:

Yellow wire - should be connected to constant 12v
Red wire - should be connected to ignition


Hope this helps.....

Cheers,

Scott

CHECK THE CLOCK BUTTON SOUNDS LIKE ITS STUCK. IF ITS A TOUCH FACE SET THE TIME THEN MAKE SURE YOU GET OUT OF THAT PROGRAM AND GO SOME WHERE ELSE IN THE SYS. IF THAT DONT WORK SEND IT IN FOR WARRANTY REPAIR,

Do the Screen Calibration. https://www.google.com/search?q=Jensen+9022+touch+screen+is+out+of+alignment ..

Try Jensen support for that detail. https://jensenmobile.com/support/ https://jensenmobile.com/shop/multimedia/cr271ml/

It sounds like there may be an issue with the mechanical components of the DVD player, specifically with the tray. Here are some troubleshooting steps you can try:

1. Check to see if the emergency eject feature is working. There should be a small hole on the front of the DVD player, and you can use a paperclip or a similarly sized object to push the button inside. This should manually eject the tray.
2. Make sure that the DVD player is receiving power. Double-check all of the connections and fuses.
3. Reset the DVD player by disconnecting the power for a few minutes, then reconnecting it and trying again.
4. If none of the above steps work, it may be necessary to take the DVD player apart and check the mechanical components for damage or wear. However, this is not recommended unless you have experience with electronics repair.

If none of these steps resolve the issue, you may need to seek the assistance of a professional electronics repair technician.

This video may help you https://www.youtube.com/watch?v=VC89DgWJlYw

1200 Watts at 12volts is 100 Amps. At least 16mm on a short run.

Your Jenson model as written only appears here on Fixya in your question. The Jenson modelling numbers don't follow what you wrote so your model number 'EOA 7P' is not valid. https://www.google.com/search?q=jensen+eoa+7p ..

hair dryer if just moisture if water [failed seal or damaged cover ] and need to unscrew ans pry apart --but if water most likely electric circuit damage

No, you cannot use a 270 watt amp kit on a 1000 watt amp. The wattage of the amp kit must be equal to or higher than the wattage of the amp it is being used for.

My guess would be internal short

Ground the parking brake wire

Your extension voltage has a problem