Top 20 Wagner 705 Power Steamer Questions & Answers

look at control fuse

Check the wiring connector you are un-plugging to make sure of the internal connection.

Question edited for clarity. Normally on the back or hidden inside https://www.google.com/search?q=iron+force+95+welder+fuse+location Seems to be an unknown make. Try the link where you live https://www.google.com/search?q=iron+force+95+welder+manual ..

To check if there is a signal from the switch on the gun, depress the switch and the wire should start to move out. If it does, the main board has a fault, if it doesn't, it may be a faulty switch.

Question edited for clarity. Some ideas in the link. https://www.google.com/search?q=Miller+250+welder%2C+brushes+unevenly+worn ..

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&ved=2ahUKEwiJm8Xqtq6DAxUvrokEHSvtAyUQFnoECA4QAQ&url=https%3A%2F%2Fwww.fixya.com%2Fsupport%2Ft29927508-deltaweld_350_help_100_code&usg=AOvVaw1Zz2ud-ECJTvyBdf5Zm-bJ&opi=89978449

Question edited for a lot more clarity, 'make model (what it is)' in the correct order. The thing about Speech to Text, is that you MUST go back through it and add punctuation or it all runs into one sentence. I did that for you as well into what I think you thought you were saying! This is an antique from the early 1950s. There is a picture of the inside wiring here https://weldingweb.com/vbb/threads/703256-Old-Marquette-Welder-wiring-question Manual for a Model 60 and 60C https://www.ebay.com/itm/115540831572 More here https://www.google.com/search?q=Marquette++Model+64+Farm+Welder+wiring+diagram ..

Question edited for clarity and order. You can't. It is 400 volts - 3 Phase.

Cutmaster 25 Manual Plasma System

https://www.westermans.com > victor-thermal-dynamics... 25mm genuine cut, 30mm maximum cut, 38mm severance; Input: 3 ph. 400V 50/60Hz 20A; Output: 80A @ 40% DC; Front panel LED's indicate status conditions for ... https://www.google.com/search?q=Plasma+cutter+thermal+dynamics+25 ..

'this welder'. The one that only you know what it is?

Hi, please for damaged wires, check that a technician has blown out dust from the rear portion of your welder after dust has been removed and double check that you've cleaned the exterior within the last 2 months. Thank you.

125EN Manual.qxd (buffalotools.com) Copy the above link into a microsoft edge browser address bar and click on it. The user guide has a lot of photos about assembly. Perhaps one will be what you are looking for. Or if you are currently using Edge, just click on the link. Good luck. Otherwise, perhaps the guys at the following link might have a picture for you. Contact them: https://reviewmotors.co/chicago-electric-welding-replacement-parts/

Power supply short circuit, it blew the fuses out when it let go. https://www.google.com/search?q=migomag+220+no+arc ..

moved you out of cars to welders TIG dead. well see if breaker in shop tripped first.

Question edited for clarity. Question moved to MiG Welders category. In the link https://www.google.com/search?q=powermig+astro+power+130 ..

It does say it is primarily a TIG welder. My guess is the the sticks are too heavy gauge for it. Did you get a manual with it? https://www.google.com/search?q=Powcon+300ST https://www.google.com/search?q=Powcon+300ST+manual ....

have you tried the idler switch and place to the hi position. this will cause the unit to rev up to full speed. see page 12 copy and paste https://assets.lincolnelectric.com/assets/ap/operatormanuals/ima572rev0f.pdf ..

Likely fuel delivery i.e. low fuel pressure at the injectors.

Causes;
Low fuel
Fuel filter plugged
Fuel supply line plugged
Lift fuel pump - insufficient fuel supply
Fuel pump (lift or module) - internally plugged
Pressure regulator not functioning properly

Minimum module (injector) pump voltage is 7VDC measured at the pump. The unit requires a battery with sufficient charge to provide cranking current to the starter and feed the fuel pump (lift and/or module).

Once running, the charging system must provide sufficient current to maintain a battery voltage in excess of 13VDC. Less than 13VDC implies failing charging system and/or battery.

wire feed motor stuck remove wire at that point squeeze trigger to see if it turns.

I replaced the one on my welder , found one at surplus center worked great. It could be simple and need the shaft lubricated or a bad connection on the motor.