Symphonic SC319C 19 in. TV/VCR Combo - Answered Questions & Fixed issues

press rcord and then it shuode come out. it will switch it selfoff then prees ejeckt.

The problem is with the vcr section, it is stuck in eject mode thinking there is a tape. This a mechanical problem that might be repairable. The tv and vcr share some of the same circuits, you can try resetting the tray in the out position as if it fully ejected the tape. Now if this does not work it means you have a gear timing problem or bad sensor.

Here's the link to the manual for the SC319C. Look on page 12.

http://www.symphonic.us/pdf/om/SC319C.pdf

I hope this is helpful to you. Bobya.

maybe its confused

Yes, but for that you will gonna have to practically dismantle the tv to access the VHS mechanics and move them yourself  manually.

sure you can check out partstore.com they have original remote for your tv.good luck.

u can go 2 buy a universal remote with a handbook 2 tell u how 2 program it lol.b alot easier.that way if u have dvd & vcr...it can b programmed 2 operate it as well as the tv!universal remotes r the best sollution lol.lazier the better lol.

You need a new VCR belt it located on right side of the vcr tray take your finger and start rotate the belt clockwise, it should release the tape. or the motor is going bad.

Hi there, This sounds like an input control error.
If you find the menu section, then choose Av inputs, you can adjust the settings, I.e. stereo Video or Av (if you are using scart leads then choose Av.
Hope this helps, Chris

If u can get to the INSIDE front, clean the window of the receiver eye.(of cause the outside also!) If the wires going to the board can be unpluged, unplug, the push it back in. Possable that the receiver eye circuit is too heated up.Put a small (square boxed computer type fan) in the back of the tv to cool it down some.If u know how to "glue" a HEATSINK to the chip to get rid of the heat, may help.
note: it is possable that BOTH regulor and universal r/c are intermittance (sometimes works, sometimes don't work)

The best way I can think of is to REMOVE the rubber band that loads the tape into the transport unit.Be KILLFULL (careful) the band is right next to the B+ (power supply) or the A\C 120volt
( and if u can find the replacement rubber bands, buy 2 kits)

Problem in tape transport mechanism, most likely...accordianman

Carriage has been set out of alignment due to improper extraction- need to repair or replace the carriage loader...accordianman

i have this problem too i dont know how to fix it either

scroll down on the channel button from channel 2. the different aux inputs should be there.there may also be a video/line in/source button on the front of the tv.if there isn't, you can buy a cheap universal remote for under $10 [even in some dollar stores for $1]
wg

If you are seeing snow on your Symphonic TV screen, it could indicate that the TV is not receiving a signal from your cable or antenna. Here are some steps you can take to troubleshoot the issue:

1. Check the cable or antenna connection: Ensure that the coaxial cable or antenna is securely connected to the TV and the wall or source.
2. Run a channel scan: Perform a channel scan or auto-programming to ensure that the TV is tuned to the correct channels and that it is receiving a signal.
3. Check the TV's settings: Make sure that the TV's input is set to the correct source, such as cable or antenna. Also, ensure that the TV's settings are not set to "mute" or "no sound."
4. Try a different device: If you have another device, such as a DVD player or gaming console, try connecting it to the TV to see if it is able to display video and sound.

If none of these steps work, you may need to contact a professional technician or the manufacturer for further assistance.

https://codesforuniversalremotes.com/remote-control-codes-for-symphonic-tvs/

Connect the converter box to TV, (usually rca connectors) connect an antenna to the box, turn it on and search for available channels. In most areas you should receive 10-20 channels.

Gave to you already.

Symphonic TV 3 Digit Remote Control Codes 198 003 053 155 189

Symphonic TV 4 Digit Remote Control Codes 1280 1384 1483 1484 1024 1031 1036 1105