20 Most Recent Symphonic ST419E TV - Page 6 Questions & Answers

program codes for Symphonic, 027,139,185,186

1131

The remotes you get from the cable company are universal and kinda cheap. ive ran across this multiple times but since i dont know what model remote you have the only advice i can give is that the code you used is not the right code if it doesnt do all basic functions (on,off for the tv,volume)its just the wrong code if the codes you stated are the only ones available the book you got with the remote should explain how to run an auto scan.hope i was some help

You may have loose connection where you put the batteries. If you open the remote, you may find a bad solder connection, or maybe the springs that keep the batteries tight is weak. Sometimes stretching them slightly will cure the problem.

I have the Xbox 360 remote... It works! ^_^ its $19.99 at best buy. When you programming it just hold down the TV and ok button. The number lights are going to stay on... put in 0445 the push the channel button up and down the TV will turn turn off/on. Then push the input button and you’re done. Hope this help.

I'm guessing at this, is TV-G a TV guide on your TV? Have you checked the MENU option or the TOOLS option on your remote?

Probably your power supply circuit has shorted, check the rectifier diodes, STR IC, Transistor, and Degaussing circuit.

Try Here:

http://www.symphonic.us/support/index.html

The TV is on protect mode. The clicking sound is the protection switchthat keep turning the TV off to prevent further damage, this happenswhen a fault had been detected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Alsoensure that the fault is not coming from a faulty receiver box sendingbad signal, check if you get same problem with no receiver boxor dvd connected.

If that does not work, and you keep having a flashingled on front of the TV, and tv turning off by itself after a while,that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1Theinternal circuits are jammed because of electrostaticcharges accumulating on capacitors, or because of a wrong voltage readby the main chip on your monitor controller board. this started theprotection circuit.

2 The protection circuit detected a wrongvoltage or abroken contact, identified an internal fault and kicked in, startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faultsthat can occur are a blown capacitor on power board, aconvergence IC has blown, or a fault on Digital board.

Check alsothe video cable or any external connection cable, if the cable is shorting, or the connector is bad, youcan get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

Electronic Replacement Parts: Plasma & LCD TVs, Appliances |

you should purchase a remote for your set to remove system OSD from showing. If you want I can post you one that is exactly matchable to your TV set.
Patrick

Hi Guys

This will help you a looooot

http://www.universal-remote.net/philipsmagnavox.html

Take your Tv to the Technician to check for you if the sensor is working properly.

I can not get to the game mode

Okay, it's not the fuse. It drawing to much current and that's the trouble. You better call the repairman.

I thought this was a free website. It sounded like it. I didn't pay much for the TV, so if I have to pay to know where to get a remote control, I can just go out and get a new one and it won't be Symphonic. Thanks,...

On the TV itself, press the MENU button. When the menu opens, "PICTURE" should be highlighted in pink and the rest of the menu items will be an aqua color. That means you are in the right place....Press the volume "up" button... this will open up the Picture menu items. When the menu opens, start pressing the channel "up" button. You will see (bright, color, etc.) options in this menu. Keep pressing the channel up button until you see "Game Mode"... the options will be ON and OFF. Use the volume "up" and/or "down" buttons to toggle back and forth between ON and OFF... if you want to watch TV, be sure to turn the Game Mode OFF... otherwise the picture will be VERY dark...

Try channel 0

Try channel 0

You have to have external jacks on TV yellow,red,white jacks these are used for hook ups to DVD-VIIDEO games, you can buy a Video converter at Wal-Marts.

Check the cable is proper. If it is proper Tuner is faulty.