20 Most Recent eMachines ET135201 PC Desktop Questions & Answers

Here you are.

The HP 970cse is a USB printer. The ET135201 has 6 USB ports

Ports

6 - USB 2.0 (2 front, 4 rear)

Connect your printer to either the front or rear ports. Note: a USB cable is not included with the printer and must be purchased separately.

Thanks, Jim

I ran into a similar problem with a dell screen. The problem was that the DVI cable wasn't receiving enough electricity. Once that was changed this problem never happened again. If is new, you can probably get a new cable from your warranty.

Most likely. The power supply will fit, but Dell machines tend to be skimpy on the extra connectors as they are custom-built. The Video card is PCIe 3.0 standard. I could not get spcifics on your manboard, but I'm fairly certain that it is not up to the 3.0 level. PCIe is backward compatible, however. Just don't expect 3.0 level performance if you mainboard only supports the 1.1 standard. Basically you are racing the Ferrari in your driveway.

Hello You may visit a computer tech to clean the cooling fan,it needs to be clean to avoid overheating or damaging your motherboard..

the manual can be found here: http://asuseee.free.fr/dl/EZ1601.pdf If you need further help, reach me via phone at https://www.6ya.com/expert/joel_63c670a84e9f6a97

add more ram is the best way of speeding up a computer you might have to many programs running at the same time putting to much strain on the CPU try uninstalling a few unnecessary programs click start control panel administrive tools computer management disk management right click on your drive select properties click tools you should see click check now click start tick in both boxes this will schedule to on restart do not have any input while chkdsk utility is in progress any might further damage your computer scroll to the bottom toolbar bottom of screen right click you can select task manager applications also processes you will see whats running on your computer and ticking over if you see something running that you dont need running select end now then you might uninstall that particular program you might have virus slowing your computer you might need to update your graphics card drivers

If your computer came with a motherboard disc the drivers could be on it

Click start control panel administrative tools computer management device manager scroll to display adapters + to expand you might see a yellow question exclamation mark ? mark ! or a red x right click select reinstall drivers

if you dont have a disk with the drivers you have to download them this should speed up your computer hope this helps you

Click Start/Control Panel/Display when the display window opens click the Appearance tab. Look down near the bottom of the window and Change the Font Size.

Click Start/Control Panel/Display when the display window opens click the Appearance tab. Look down near the bottom of the window and Change the Font Size.

Thirteen quick beeps at startup on an eMachines E520 usually indicate a problem with the laptop's RAM (Random Access Memory). This could mean that the RAM is not properly seated in its slot, or it could be a sign of a faulty RAM module.

Here are some troubleshooting steps you can try to resolve this issue:

Turn off the laptop and disconnect it from the power source.
Remove the battery from the laptop.
Locate the RAM compartment on the bottom of the laptop.
Check to make sure that the RAM module is seated properly in its slot. You may need to remove and reinsert the RAM module to ensure a proper connection.
Replace the battery and turn on the laptop.
If the problem persists, try removing the RAM module and testing it in a different laptop or using a different RAM module in the eMachines E520 to determine if the problem is with the RAM module itself or with the laptop's RAM slot.
If none of these steps solve the problem, it may be necessary to contact a computer technician for further assistance..

1. Boot the computer to the boot menu: To do this, restart the computer and press the appropriate key when prompted to enter the boot menu. On most eMachines computers, this is the "F12" key.
2. Select the CD/DVD drive as the boot device: Use the arrow keys to select the CD/DVD drive and press the "Enter" key to boot from it.
3. Insert the Windows ME boot disk: Insert the boot disk into the CD/DVD drive and restart the computer.
4. Choose the "Start Computer with CD-ROM support" option: When prompted, choose the "Start Computer with CD-ROM support" option.
5. Run the Windows ME setup program: The setup program should start automatically. Follow the on-screen instructions to install Windows ME.
6. Format the hard drive: During the setup process, you will be prompted to format the hard drive. Choose the "Full" format option to erase all existing data and perform a complete factory reset.
7. Install Windows ME: Continue to follow the on-screen instructions to complete the installation of Windows ME.

After the installation is complete, the computer should be in a factory reset state and you can begin setting it up as a new system. Please note that resetting your computer to the factory settings will erase all personal data and installed programs, so be sure to back up any important data before proceeding with the reset.

Larry picks up a question from 2015 ;>) Larry Ng Feb 07, 2022 no PC model told hopeless If desktop, the jumper on the MOBO marked PW_CLR on most. Never laptops

device manager 1 of 10000 model ODD optical disk drives made, each drive made has LIMITS some only do CD ROMS BD is blue ray , FIY if missing or maked with red or yellow errors or shows up as unknown that all means DRIVER IS BAD , wrong or missiong NO PC Told so can not tell you how to fix that, lacking such a key fact . (but is at your oem makers PC support page under DRIVERS)

moved you out of monitors and into laptops, only forum. emachines full model not old like this example E525-901G1Mi windows 7 loaded day1.

• the switch is bad Lid close switch
• set wrong in power settings.
• or the driver is missing that makes this switch work.

so why not just assign the sleep mode, to auto sleep then on what does the power button do in settings, set to do nothing or set button to only sleep . (3 choices here) or let auto sleep do the work, set. set to say 5min idle. the switch is inside it deep and if you rip it out as you go there most noobs break 2 or 3 FFC cable jacks and now it is bricked and $300 mobo wrecked emachines or junk grade, made by Acer.com owned now and that maker does NOT have service manuals making service a royal Pain. best is work around the problem as I just told how. or ask any shop to fix it. they do know how.!!!

Larry has the answer. Larry Ng Feb 07, 2022 no reason stated, the OS reloaded, ?that? what does reset mean to you? and why.? (selling PC or PC infected?) what:"? ahhhh a Netbook sold new with XP or W7, lost the install media? page 22 in your manual shows that you must create recovery media day one, new. if not , it is GONE. https://www.emachines.com/ec/en/US/conte... ..

Check the hdd is setup correctly and set as first boot device. Ensure there is no external drive/usb installed.

e525 lapTOP OR? FOR GOT TO TYPE THE "e"????? 2009 MADE? 13 YEARS AGO? 2 causes (of many but 2 are CLASSIC COIN cell is now dead CMOS and boot order lost. or hdd bad the cure is, new coin, and reset bios and set boot order to hdd0 first the hdd must pass smart tests. or all hope is gone foR IT. ask how. that error means boot order wrong or hdd is bad. boot fails missing on hdd is bad HDD 99% the time. NO COIN LASTED 13 YEARS. AND MOST HDD SAME THING. UNLESS PUT IN TIME CAPSULE IN Ln2, CRYRO FREEZED. now the BAD NEWS the COIN cell is soldered down to the MOBO and is not a normal CR2032 it is ML1220 rechargeable listed as 5 year life.(MAKER OF COIN) so you fOUND this PC in a garage sale dead for $1?>???? no history told at all, ever fix old cars. ? emaciates now owned by Acer and Toshiba does this nasty trick "solder down" e525 actual there it is, in all its glory, lots of screws to get and soldering pen to release it, I cut the wires up top and solder then new coin to top wires. and not touch mobo PADS that is a huge hint there.(do no harm)

how to do this physically or just putting back a new OS there. or what to buy it. or what what parts are unclear.

• buy new,hdd, or 100x better SSD
• install it.
• install what ever OS you want. w7 -64bit new.

age 2011,

classic case most old PC on earth slow. No PC told at all the model, wow.

1. hdd full
2. OS virus infected. N
3. HDD bad, fails smart test.
4. memory full, add more or git ride of autoloading apps,

No PC model told. desktop (vast there are) same on all desktops made one side of case. remove 2 cable to drive remove 4 side screws from side of drive to cage. remove drive, slides out. some PCs the drives have caddies. no PC told the manual is here https://www.emachines.com/ec/en/US/content/support.html