SkyScan 86742 Digital Atomic Wall Clock - Answered Questions & Fixed issues

1) Pull the batteries and replace them, or gently insert a straightened paper clip into the "reset" hole in the back of the clock. The clock will beep.

2) Press the "receive" button" so the clock sets itself. The default time zone will be "EA".

3) Press the "adjust" button untill the time zone is showing (rather than the day-of-the-week).

4) Press and HOLD the "set" button down untill the hours digits start to flash.

5) Now press the "set" button again six times. The time zone characters will flash.

6) Press the "adjust" button untill your time zone appears.

7) Press the "mode" button to return the clock to normal operation.

8) Press the "adjust" button to display the day-of-week.

If your outside temperature is not showing on your clock, that may mean that the clock and the transmitter have lost their connection. To reconnect them you must first take the batteries out of both of the units for 15 minutes. First put the batteries back into the transmitter, and then the clock. Let them sit side by side inside your home. When both the indoor and outdoor temperatures show on your clock with the same reading, or within two degrees of each other, then you may put your transmitter back outside. Remember to keep the transmitter out of the direct sun in a dry place. Also keep it away from metal, which can affect the readings.

Which question was your original question?

Remove battery for a minute, reinsert battery and allow clock to settle (15 min) now try.

I assume you mean the LED Display unit..... If that is starting to go..... you need to buy a NEW ONE.,...... unless you are really good with a Soldering Iron and also know Electronics.... and then getting the Wiring Diagram will be a Major Problem

If the moving spindle, where the LEDs are attached is either not moving, or jittering when power is applied, it is most likely that the PNP transistor (only one on board) is burnt and needs to be replaced by the like of 2N3906. It can be located next to where the speaker wires (x4) are soldered to the PCB, and next to the snubbing diode.Bic Tran

Clock shouldn't lose time if it is receiving time signal. Do you have the signal indicator showing?If not suggest you take the batteries out and reset the clock, making sure that you do not set a time.

On my similar model, there are 4 buttons on the back. The 3rd button starting at the left is labeled ALM. You should be able to turn the alarm off by pressing that button.

Sometimes all it needs are new batteries.

Hellohttp://www.atomicclocksstore.com/Get into this link. You can download the user manaul for your clock from here. Get a serach over the site.

HelloGet into this link. You can download the user manual for your clock from here. You will get instructions to adjust time.http://www.atomicclocksstore.com/

Hellohttp://www.atomicclocksstore.com/Get into this link. You can download the user manual for your clock. OK.

Hellohttp://www.atomicclocksstore.com/Get into this link. You can downlaod the user manual for your clock. OK.

Hellohttp://www.atomicclocksstore.com/Get into this link. You can download the user manual for your clock. OK.

Hellohttp://www.atomicclocksstore.com/Get into this link. You can download the user manual for your SkyScan clock from here.OK.

Hello

The SkyScan ATOMIC Clock With the Skyscan Atomic Clock, you have the most accurate timepiece within the continent. It can receive the time signal transmitted by the National Institute of Standards and Technology (NIST), which is regulated by 3 atomic clocks and deviates less than 1 second within 3,000 years. The NIST broadcasts the time signal (WWVB, 60kHz) continuously from Fort Collins, Colorado. This signal can be received anywhere in the continental USA that long wave (AM) radio reception is possible with a portable radio. It is expected that the signal can cover a distance of over 2,000 miles from the transmitter. Therefore, your clock will receive the signal within the broadcast range anywhere an AM signal can be received; generally the signal cannot be picked up in massive metal and concrete structures unless near a window. In addition, some environmental effects (see next page) may affect the transmitting distance.

HelloGet into this link. You can get user manuals for many models of Skyscan clocks there. OK.http://www.atomicclocksstore.com/skyscan-atomic-clock-model-86931-manual

How do I turn off the alarm clock on model number 87315? [email protected]

To purchase an outdoor sending unit? Please give us all the information you know. Thank you.

FixYa Support

Yes you can order replacement transmiters. Just click on the link below to order one.

http://www.skyscaninfo.com/content/