20 Most Recent Minolta QMS PagePro 9100 Laser Printer - Page 2 Questions & Answers

Check near where the paper comes out for a little plastic flag that can move up or down. If it's the model I'm thinking of that has that, It's possible it has stuck up, making the printer think the paper bin is full. If so, you should be able to just flick it down and it'll be alright.

If not, well, maybe someone else can help you out, this is just the first thing I thought of.

This is an error when it senses there are too many pages that have been printed and are sitting in the bin.

Take a close look at the flaps hanging out the exit for the printer. They should move up and down freely. If one of them is stuck up, broken or dislodged, you'll get the bin full error. The flaps on the other end (side you can't see) have little flags that sweep between photo sensors and tell the printer in the tray is full and if paper has exited the printer into the tray

output bin is full

plz try with a new tonner cartridge

UNCHECK PRINT TO FILE CHECK BOX

Attentively examine the sensors of the passing of the paper. 1. The Sensor of the arrival of the paper. 2.датчик passings , he in medium device. 3. Datchih leaving the paper. Usually can be обрыванеи papers, or more often when paper извлкают damage the sensor and he comes out of its place. You should visual to make sure that sensor in its full tilt and есл no correct (it).

Its under the Admin Menu under Start Up Options.
Page 160 in the manual.
Good Luck

In the middle of the paper path at the output bin is a plastic tab that can hang up. Push it down to see if this enables printing to resume.
That tab is connected to a lever that you can see when the top cover is open.
Good luck.

download image to parallel port

If you know how to dismantle the printer that will be better so you can clean the entire printer and check all the possible things that maight causing the paper jam....

I found out that it was some (vector) snowflakes we had in the art that had gradients that caused the printer to freeze.

We removed (in Adobe Illustrator® CS3) all of art work then replacing it on piece at a time, printing OK until we added the snowflakes. Turning the gradients into just halftones was our solution. The printer representative is going to give our printer a memory upgrade for free.

Change it back. Here is your manual. https://www.manualslib.com/manual/1001522/Konica-Minolta-Bizhub-Pro-1050.html?page=110#manual There is also a Service Manual available for it if you ever need it.

MINOLTA EP1050 GENERAL Service Manual download ...

Elektrotanya https://elektrotanya.com > minolta_ep1050_general.pdf Download MINOLTA EP1050 GENERAL service manual & repair info for electronics experts. ... MINOLTA EP-1080 CS-PRO A3-COPIER 1993 SM service manual. MINOLTA EP-1080 ... ..

Question edited into written English. Misfeed Error, or Timing Error. You need dealer service. This is a Professional Machine. The fuser only heats the toner to set it on the paper. It is nothing to do with jams.

Yes the Fuser unit that part that is very hot well one of the sensors has detected a very hot temp. get a tech out o look at and reset it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

The error code C-1028 on a Minolta Dialta 520 photostat machine typically indicates a problem with the paper feed system. Based on your description, it seems that you have already replaced the PWB-B Board and checked all jacks, but the problem persists. In this case, there could be a few other potential causes of the error.

• Paper feed motor
• Main control board
• Gears or other parts in the paper feed system
• Paper feed sensor

Regarding the Bet Pin, it could be the name of a specific pin on the PWB-B board or in the paper feed system, but without more information about the specific location or context it is hard to say exactly what it is referring to. It is recommended to consult the service manual of the machine, or contact the manufacturer or a professional technician for further assistance. They will be able to diagnose the issue and provide the necessary steps to fix it.

Question edited for spelling 'tonner' to 'toner'. It is a common error. Are you using 'Copy', none OEM cartridges? https://www.manualslib.com/manual/89897/Konica-Minolta-Bizhub-C20.html?page=307&term=not+installed+toner&selected=1#manual More here https://www.google.com/search?q=Minolta+Bizhub+C25%2C+%22Not+installed+toner%22 ..

Something to do with main motor. paper jam. Or bad main motor.

Limited help in the link https://www.google.com/search?q=Minolta+MS6000+C2+Error+code ..

Konica Minolta FS-517, FS 518 FS 508