La Crosse Technology Wireless Thermometer WS9007UIT - Answered Questions & Fixed issues

Bring the outdoor sensor inside. Take batteries out of both the sensor and the main unit. Wait 10 minutes. Put batteries in remote sensor. Then put batteries in main unit. Don't touch any of the buttons for 10 minutes or until the outdoor temperature is displayed. If still not displayed after 10 minutes then try again.

Question edited for clarity. Full 'make model (what it is)'. Did you put batteries in both units and in the right order, sensor first? Step 1: Insert 2 fresh AA, batteries into the TX29U-IT sensor according to the polarity marked in the battery compartment. Step 2: Insert 2 fresh AAA, Alkaline batteries into the wireless thermometer according to the polarity markings. Step 3: After 5 minutes place sensor outside in a shaded location. https://www.lacrossetechnology.com/products/WS-9160U-IT#support Retired unit so no further warranty or parts. You can still get one on Amazon

La Crosse Technology WS-9160U-IT Digital Thermometer ...

Amazon.ca https://www.amazon.ca > Technology-WS-9160U-Digita... Digital thermometer with wireless remote and clock; Remote sensor transmits from up to 330 feet; records daily high and low temperatures; Receives weather ... Rating: 4.4 · ‎ 7,970 reviews · ‎ $31.50 · ‎ In stock ..

That model is retired. There is no support for it

Without specifics: Here is a good start for troubleshooting:https://www.lacrossetechnology.com/media/catalog/product/s/8/s84060_faqs_092617.pdf

You had a loss of power at some point reset it,.

https://www.youtube.com/watch?v=GW_zJur00t8 End of video mentions the CH snooze, but unsure if that will help you. WS 9047TWC IT Wireless Forecast Station with Pressure History

S84107 Wireless Color Forecast Station This video shows the basic setting for language. Note model number.

You are using a wireless system that transmits signals between the outdoor sensor and the indoor receiver. They are not a perfect match. You cannot make adjustments, thus if your lucky, the factory matched up the devices prior to the sale. You may contact Lacrosse for a replacement outdoor temperature device.

https://www.manualslib.com/manual/91064/La-Crosse-Technology-Ws-1612.html

Most LaCrosse weather station manuals are available here: http://www.meade.com/support/manuals/ or on the product page (see the Support tab). Using the search feature on the support page, I found three models which start 308-1414. Two of these differ in the color of the case of the weather station. Hover over the picture of any of these weather stations and click on the More button to go to their product page. The direct link to the manual for the 308-1414MB is http://www.lacrossetechnology.com/media/catalog/product/3/0/308-1414m.pdf . This product page is http://www.lacrossetechnology.com/308-1414mb-weather-station/ . The manual for the 308-1414W/308-1414B is http://www.lacrossetechnology.com/media/catalog/product/3/0/308-1414.pdf . The product page for the 308-1414W is http://www.lacrossetechnology.com/308-1414w-weather-station/ . I hope this helps. Cindy Wells

in the clock set mode change from 24 to 12

http://www.lacrossetechnology.com/media/catalog/product/w/s/ws-9611u-it.pdf Here is the method used to set up the outdoor transmitter with the base station

You have to set these, if you don't have a manual you can usually obtain one on line or contact La Crosse

It means OverFLow - the display unit can read from -39.8°F to 139.8 °F and it is getting a signal from the sending unit that is lower than -39.8 or higher than 139.8. This happens when the sending unit goes haywire (or, not likely, when temperature out doors is REALLY lower or higher than the range). Replace the sending unit. If you really like the product, I suggest you buy another of the same model. It will come with a new sending unit and that will be read by both of the displays if they are within 80 ft of the sending unit. Good luck.

You may download a copy of the manual at http://www.lacrossetechnology.com/9047itc/manual.pdf It's a PDF file so your viewer should be able to magnify it to just about any size you want.

http://www.manualslib.com/products/La-Crosse-Ws-8256u-2940322.html Hi Vickie....try this....good luck to you. Regards, Dennis

station is not giving me an outside reading

The manual for the thermometer is available on the LaCrosse site: http://www.lacrossetechnology.com/7034twcit/index.php . The direct link is http://www.lacrossetechnology.com/7034twcit/manual.pdf .

Put the batteries in the remote(s) first. (If you need to reset the units, pull the batteries from the indoor temperature sensor and the remotes for 10 minutes before restarting.) With the remotes and indoor sensor 3 to 5 feet apart, put the batteries in the indoor temperature sensor. Then wait 10 minutes before pressing any buttons. Once you have confirmed communication between the units, then move the remotes to their final location (not more than 330 feet away minus 30 feet for external walls or windows and 20 feet for each internal wall between the units.)

I hope this helps.

Cindy Wells

Bring the outside sensor inside. Take the batteries out of the sensor and out of the main unit. Wait 10 minutes. Put the batteries back in the remote sensor. Put the batteries back in the main unit. Do not touch any of the buttons. Wait 10 minutes. If the remote temperature is not showing within 10 minutes, try again. Once the remote temperature is showing, you can set the clock.