La Crosse LaCrosse Technology Professional Weather Station - Page 8 - Answered Questions & Fixed issues

Do you have a setting for the power line frequency? Some devices get their timebase from the power line frequency and if your powerline is 60 Hz, but you have it set on 50 Hz, then it will speed it up because of the 10 extra cycles per second.

The sensor should flash briefly when you put in good batteries. Afterwards it should flash about every couple of minutes. If you have a voltmeter check the batteries are at least 1.3 volts (the voltage will drop when they get colder). Ideally they should be about 1.4-1.6 V. Try cleaning the battery compartment contacts and springs with a cotton bud and alcohol. If the contacts look rusted then use fine emery paper or scrape with a screwdriver to remove the rust and tarnish. Clean the ends of the batteries by rubbing with a tissue or cloth. When inserting new batteries twist them inside the battery housing to help make better contact. Another thing you might try is to use a screwdriver to very carefully stretch the springs in the battery compartment a little to allow better contact. (Warning do not pull the spring too hard so as not to damage it) If using new batteries does not help then the sensor may have a fault. If the led on the outdoor sensor is flashing but the indoor sensor does not pick up the signal you can try putting the indoor sensor closer to the outdoor sensor. Otherwise you may need to re-tune the indoor sensor to the correct frequency (there is a small adjustable screw inside).

Hold the CLK button, and then the ADJ button. https://fccid.io/OWF-WSRX/Users-Manual/Users-Manual-171217

search for it at this link...https://www.manualslib.com/3/331nc.html

Radio Frequency communication may come and go occasionally. This can be normal in some environments (e.g. moister climates). If transmitter signal is lost, please wait 2-4 hours for the signal to reconnect on its own. Here is a link to the User Manual for your product. https://www.lacrossetechnology.com/media/catalog/product/w/s/ws-8119u-it__faqs_1.pdf

try new test leads first. even if the unit is miscalibrated, you should get the same measurements from the same components/circuits. you'll need to send the unit to a calibration center, or the manufacturer, to get it zeroed out, if you still need to afrer getting new test leads

Here is your answer: http://plumbr.eu/blog/how-do-leak-detectors-work-plumbr-case-study

Tape measure and manual for sale on eBay. https://www.ebay.com/i/113701075337?chn=ps

1. Disconnect the test leads from any energized circuit and then from the instrument. 2. Turn the range switch to the "OFF" position 3. Slide off the back case battery cover. 4. Remove the battery from the compartment and unsnap the battery connector. 5. Replace the battery with a 9V transistor type battery (NEDA # 1604), For maximum battery life, alkaline cells are recommended. 6. Reverse the above procedure to complete replacement.

Not sure but if you press the clock button on the side; ? Press to start or stop a WWVB time signal search (which is what I think your clock is set to) ? Hold for 3 seconds to set time/calendar, etc.

Have you tested the rain gauge using the calibration procedures on page 21 of the manual? Specifically confirming that the bucket is emptying about every 25 drops. https://www.acurite.com/media/manuals/01536-instructions.pdf

no info -generic answer check with manufacturer -owners manual online search uging make and model of mystery unit

battery or internal damage

check Google weather, or check environment Lesotho weather station. :-)

Depends on the make of the scales. Check manufacturer.

Hello Anthony, I sent you a link so you can find out the manual of the tester Sperry DM-210a and another where you get an explanation of the operation I hope you can solve your concern Greetings Franco Dosil Hola Anthony, te envio un link para que puedas descrgar el manual del tester Sperry DM-210a y otro donde te dan una explicacion del funcionamiento Espero que puedas resolver tu inquietud Saludos Franco Dosil https://www.hunker.com/13414165/how-to-use-a-sperry-dm-210a-meter https://greenlee-cdn.ebizcdn.com/media/52058078REV01.pdf https://www.hunker.com/13407450/instructions-for-a-sperry-dm-210a

Try checking this site for the manual. https://www.manualslib.com/

I do not believe that you can buy these separately. They are factory programmed and paired together.

Simple, remove the batteries, leave a time without, then put back in place, will return to factory settings alone

You need to describe the brand, model and type of instrument you are seeking information on. Have you tried pressing the C/F (degree) button?