NEC VT460 Multimedia Projector - Answered Questions & Fixed issues
Nec vt540 vt540k
probably needs filters cleaning or a new lamp replacement.
11/15/2013 11:32:21 PM •
NEC VT460...
•
Answered
on Nov 15, 2013
•
444 views
Vt575 pROJECTOR
My VT440 says this when it gets to it's pre-defined service life. (a certain amount of hours)
As long as you pop the filters out regularly and clean them (I use a vacuum cleaner) you shouldn't need to replace them.
After that, go into the projector options (with the remote control) and reset the factory defaults... otherwise it has no idea that you have actually changed the darn thing and keeps complaining no matter what! =-]
6/18/2012 10:03:45 AM •
NEC VT460...
•
Answered
on Jun 18, 2012
•
279 views
Cannot get the remote to
Problem is not clear. Are you trying to use remote of the projector to move the slides? And slides from what? A PowerPoint presentation?
If you are using a computer, use the computer to change what is shown. You cannot use the remote of the projector for that.
Provide more information to help you better.
9/26/2011 2:46:56 AM •
NEC VT460...
•
Answered
on Sep 26, 2011
•
502 views
How do i make text
Hello
There is no provision and adjustments to make the text size only to your projector. Picture as a whole can be adjusted with MAGNIFY (+) or (--) button. OK.
9/2/2011 5:02:01 PM •
NEC VT460...
•
Answered
on Sep 02, 2011
•
30 views
Red blinking 7
the bulb has failed or failed to start due to a bad connection.
---
Please dont forget to vote this answer was helpful.
Many thanks
------
3/4/2011 5:41:53 PM •
NEC VT460...
•
Answered
on Mar 04, 2011
•
103 views
What is pc contol
When using a special cable, pins 1, 4 and 7 of the PC control connector on the rear of the projector are used to receive RS232 serial commands from the PC to control various functions remotely in the projector.
3/2/2011 11:53:57 AM •
NEC VT460...
•
Answered
on Mar 02, 2011
•
89 views
I have a vt580 i
Hi, you definitely need the remote control to turn on the projector, without it you cannot operate the projector......
11/22/2010 10:35:56 PM •
NEC VT460...
•
Answered
on Nov 22, 2010
•
92 views
I cant find the air filter cause im dumb so where
Look at the photo above. Find the small grill on the right, you can just see it in the photo. Directly below is a narrow cover with a cutout for your finger nail. Insert finger nail and push down. Out it slides.
11/10/2010 7:23:04 PM •
NEC VT460...
•
Answered
on Nov 10, 2010
•
59 views
My projector can't on
I assume you mean it has no power? This is fairly common with the NEC VT460,VT470,VT595. The power board/Power Supply has failed. I can usually repair or replace the power supply for $170
If you're familiar with electronics you can try checking the main power fuse by removing all the screws on the bottom of the projector & taking the cover off. The fuse is located just next to the ac plug. Test it using a continuity tester with long testing probes. If it's ok then the power board is bad & needs repair.
If it's bad replace with the same type fuse. You can bring the fuse to Radio Shack for identification or look on the power board next to the fuse holder for fuse amperage.
If you would like a repair please contact me at
[email protected]
Thanks & good luck,
Jim
10/2/2010 6:52:17 PM •
NEC VT460...
•
Answered
on Oct 02, 2010
•
422 views
My image is back to
I don't have the specific incantations for this, but work through the setup menus and you should see a series of selections for ceiling/floor, front/back etc. This is selectable in that fashion.
I will try to locate the specific menu in the meantime.
Dan
9/28/2010 12:47:47 PM •
NEC VT460...
•
Answered
on Sep 28, 2010
•
47 views
Not finding what you are looking for?