20 Most Recent
NEC VT460 Multimedia Projector - Page 2 Questions & Answers
How do i make text
Hello
There is no provision and adjustments to make the text size only to your projector. Picture as a whole can be adjusted with MAGNIFY (+) or (--) button. OK.
9/2/2011 5:02:01 PM •
NEC VT460...
•
Answered
on Sep 02, 2011
Red blinking 7
the bulb has failed or failed to start due to a bad connection.
---
Please dont forget to vote this answer was helpful.
Many thanks
------
3/4/2011 5:41:53 PM •
NEC VT460...
•
Answered
on Mar 04, 2011
What is pc contol
When using a special cable, pins 1, 4 and 7 of the PC control connector on the rear of the projector are used to receive RS232 serial commands from the PC to control various functions remotely in the projector.
3/2/2011 11:53:57 AM •
NEC VT460...
•
Answered
on Mar 02, 2011
I have a vt580 i
Hi, you definitely need the remote control to turn on the projector, without it you cannot operate the projector......
11/22/2010 10:35:56 PM •
NEC VT460...
•
Answered
on Nov 22, 2010
I cant find the air filter cause im dumb so where
Look at the photo above. Find the small grill on the right, you can just see it in the photo. Directly below is a narrow cover with a cutout for your finger nail. Insert finger nail and push down. Out it slides.
11/10/2010 7:23:04 PM •
NEC VT460...
•
Answered
on Nov 10, 2010
My projector can't on
I assume you mean it has no power? This is fairly common with the NEC VT460,VT470,VT595. The power board/Power Supply has failed. I can usually repair or replace the power supply for $170
If you're familiar with electronics you can try checking the main power fuse by removing all the screws on the bottom of the projector & taking the cover off. The fuse is located just next to the ac plug. Test it using a continuity tester with long testing probes. If it's ok then the power board is bad & needs repair.
If it's bad replace with the same type fuse. You can bring the fuse to Radio Shack for identification or look on the power board next to the fuse holder for fuse amperage.
If you would like a repair please contact me at
[email protected]
Thanks & good luck,
Jim
10/2/2010 6:52:17 PM •
NEC VT460...
•
Answered
on Oct 02, 2010
My image is back to
I don't have the specific incantations for this, but work through the setup menus and you should see a series of selections for ceiling/floor, front/back etc. This is selectable in that fashion.
I will try to locate the specific menu in the meantime.
Dan
9/28/2010 12:47:47 PM •
NEC VT460...
•
Answered
on Sep 28, 2010
There is a red border
HI
your red LCD penal is not working suspected loose connector or faulty LCD panel or main Board
ANS BY
M.R. Mumbai & Dubai
9/2/2010 7:09:52 AM •
NEC VT460...
•
Answered
on Sep 02, 2010
I think the lamp life
www.necvisualsystems.com/documents/.../vt460_560_660usermanual.pdf
www.support.nec-display.com/...service/.../manual/.../vt660_important_info.pdf
Above are your manuals for use and repair.
Sometimes there is a resettable thermal fuse near the lamp, this may have to be reset before it will go again.
Sometimes there is a "Counter" to be reset too, but not always.
8/4/2010 8:40:24 AM •
NEC VT460...
•
Answered
on Aug 04, 2010
Dell d600 will not transfer laptop screen image to
Press <Fn><F8> to switch the video image to the integrated display only, the integrated display and an external CRT monitor simultaneously, an external CRT monitor only, the integrated display and external DVI monitor simultaneously, and external DVI monitor only. HOpe this helps
2/19/2010 6:25:03 PM •
NEC VT460...
•
Answered
on Feb 19, 2010
Not finding what you are looking for?