20 Most Recent Mitsubishi WS-65511 65" Rear Projection Television - Page 6 Questions & Answers

Reference this:

Mitsubishi TV Codes

Hope this helps

Ur convergence it dead.U know how to solder right?Tries this websites for the convergence kit.Tv Repair World.com,Shopjimmy.com,Ebay.com or Partstore.com

yes, you need a philips screwdriver, pull the speaker grill off, remove the 4 or 5 screws along the bottom of the screen assembly, unlock the 2 electrical plugs and remove them from their ties, lift up on the screen assembly and remove it. turn it upside down and remove the 4 screws holding the bottom of the frame on, remove frame bottom, slide screen protector out, re-assemble, bingo, no glare.

Bad filters in the main microprocessor. good luck.

No,it for data recovery mainly.Ur HDMI connection it work?If not tries another HDMI cable usally work.

Change the whole board.
The IC is deffective it dead.
95% of the times the board with IC will dies. Boards with burn parts,will have to much juice to the IC it will die.

Ur power ic inverter board is dead.
U need a new one.

revisa la convergenci que esa es la que ocaciona ese problema

You should be able to use the device button on the remote control. If this does not work, try going into the menu and disable the home theater mode. The home theater mode locks the TV to input 1. I believe that it is in the advanced menu from the main menu.

I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. (Two Thumbs Up)
Please Note: If you can not rate this post with the highest rating, then please do not leave any rating. I am doing this for free and I do not think that any rating other that the best is needed.
If you need further assistance please comment to this post and I will try to help you further.

yea this pictilar model kwon for this it is the vertical drive ic i recommend checkint it fist check fuses may fix ur problem impossible to geusse

hello what is the model numbrer of your tv?
i can help you
what is exactly the sympotm rigth now?

vote if help u

Testing by FixYa Staff

Please do not rate this post!

We apologize for any inconvenience.

green is base line center and some times is not adjustable
.Did you replace both convergance chips?
also there are 6 , 2.2 ohm res that get out of
tolarance. check them first

There are several things that you can do for troubleshooting this symptom.

First, you can test the remote; if you have a camcorder you can film the remote while it is transmitting. The camera can see the infrared diode on the front of the remote. Just turn the video camera on record and shine the front of the remote into the lens of the camera. If it is flashing then the remote is working.

You may want to unplug the television set for 30 min and then plug it in and see if that fixes it.

As you stated in your post, neither the remote or the front panel work to turn the television. It is possible that you have a dead set.

I would recommend that you contact a local service center to come out and diagnose the problem that you are having.

I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. (Two Thumbs Up) If you cant rate this post with the highest rating, then please comment to this post and I will try to help you further.

more than likely. and you will have to solder it in

Ok, try this first. After attempting to turn on set after it shuts off push and hold the MENU and INPUT buttons at the same time on the front of the set for 10 seconds. This should acccuate the self diagnostics function in the micro and the power LED should start blinking a two sequence code. That code will narrow things down.

NEEDS ANOTHER BULB. BULBS ARE PRICEY, BUT EASY TO INSTALL.

Yeah you were mislead. Those switches are known trouble makers. You can just leave the switches disconnected and the set will operate just fine with the remote with no problems. If you want to fix the control panel, just replace all the switches on it. They are cheap. The Mitsubishi part number for the switches is 432P089010