20 Most Recent Scotts Company Scotts Turf Builder Classic Drop Spreader 73730 - Page 6 Questions & Answers

try this:
After doing a search I found this:
From Lesco website

For 18-24-12 %50 PPSCU

Product Application Rate:
*LBS PER 1000 SQFT 4
Coverage:
* 12000
Craftsman 3
Craftsman Drop 7
Cyclone 4.25
Earthway 14.25
Lely 4.5
LESCO HD-1 7
LESCO R-94 7.5
LESCO Rotary (80# & 100#) 15
Ortho 3
Precision 6
Red devil 6
Republic 3
Scott's Accu Green 7.25
Scott's Easy Green 26.25
Scott's R7- X F.5
Scott's R8-A J.5
Scott's Speedy Green 1000 6
Scott's Speedy Green 2000 7
Scott's Speedy Green 3000 6
Spyker 4.5
True Temper 1500 \ 5000 5.5
Vicon 28
_________________________
I was married by a judge. I should have asked for a jury.
-- Groucho Marx

I found this:

For 18-24-12 %50 PPSCU

Product Application Rate:
*LBS PER 1000 SQFT 4
Coverage:
* 12000
Craftsman 3
Craftsman Drop 7
Cyclone 4.25
Earthway 14.25
Lely 4.5
LESCO HD-1 7
LESCO R-94 7.5
LESCO Rotary (80# & 100#) 15
Ortho 3
Precision 6
Red devil 6
Republic 3
Scott's Accu Green 7.25
Scott's Easy Green 26.25
Scott's R7- X F.5
Scott's R8-A J.5
Scott's Speedy Green 1000 6
Scott's Speedy Green 2000 7
Scott's Speedy Green 3000 6
Spyker 4.5
True Temper 1500 \ 5000 5.5
Vicon 28

There is no correlation between the letters on your C2 to the numbers that are now used on newer spreader models. Your best bet is to do your own test. Measure a 50 x 20 foot area in your lawn. Place enough material in your hopper to cover 1000 sq ft. Set your spreader setting on a ¼ of your spreader setting range. Spread the material over the 50 x 20 foot area. If you have product left over you increase your spreader setting. If you come up short you decrease your spreader setting. While this is not exact it will give you the ballpark setting

www.scottsprofessional.com try there

Simple. Assume they are shipped to store properly calibrated. (Probable).
Go to store, set a unit on 8 (Mid-range).
Use a small straight-edge ruler to measure the travel from cosed to open.
Go home, set yours the same, using the attqachment of the wire to the slide mechanism. (If you can't figure this out, you should just buy a new one.)

I called Scotts, and according to them the Edgeguard Deluxe uses the same settings as the SpeedyGreen 3000.

jb weld

If the wheels turn( that is you can push the spreader easily) but the vertical shaft that spins the broadcasting plate doesn't, seems like the gears connecting the axle to that vertical shaft are worn; but if the wheels just slide along the gropund without turning then it would seem something right under the bin is keeping the verical shaft from turning. But I'm NOT an expert; I'm looking for an answer myself,

Ensure the membrane is protected with sand before laying the stone to avoid piercing the membrane.

All questions need full 'make model (what is is)' as first 3 words please. Very often, issues like this are a known fault and users tell the fix. You need to track down where the screech is coming from? Wheels Drive Belt Bearings Piston rings Or it may be battery operated? ..

It looks like you meant 'Wahl', this is why upper case letters are important for 'proper names' because Spell check won't alter them. Here are the parts diagram and suppliers, including Wahl themselves. https://www.google.com/search?q=wahl+kennel+pro+model+8800+parts+diagram You can safely ignore the answer from the African Prince as he is just copying and pasting from AI Chat GPT4. ..

Here are some steps you can follow: Check the Seals and O-Rings: Release the pressure: Make sure there's no pressure in the cylinder by releasing the pressure release valve. Unscrew the pump: Remove the pump to access the internal components. Inspect the seals and O-rings: Look for any damaged or worn-out rubber seals. Check the rubber seal at the bottom of the tube (where the plunger sits) and ensure it's in place. Examine the one-way valve (usually at the bottom of the tube) and clean it. Lubricate it with silicone grease. Lubricate the rubber washer on the plunger with silicone grease and reassemble it in the tube. Reassemble the pump: Put the plunger back into the tube and lock it with the handle. Test the sprayer: Pump it up and check if it maintains pressure without leaking. Inspect the Handle and Hose: Handle connection: Ensure the handle is securely attached to the cylinder. Hose inspection: Check the hose for kinks, twists, or blockages. Straighten out any kinks and remove debris that might be blocking the hose. Check the Nozzle and Wand: Nozzle adjustment: Adjust the nozzle to the desired spray pattern. Wand inspection: Examine the spray wand for clogs or obstructions. Lubricate O-Rings and Seals: Apply silicone grease to the O-rings, seals, and other moving parts to ensure smooth operation. Test the Sprayer: Fill the cylinder to the desired level (avoid exceeding the maximum fill mark). Screw down the pump firmly to create an airtight seal. Manually operate the pressure release valve to ensure it's working.

As a customer, the advantage is that I don't have to drive to the florist. Saves time and gas. I could make a phone call, but then I wouldn't see the available flowers.