Top 20 Mitsubishi WS-65315 65" Rear Projection HDTV-Ready Television Questions & Answers

http://elektrotricks.blogspot.com/ http://electrotechnician.blogspot.com/ http://electronicshelponline.blogspot.com/ http://homenol.blogspot.com/ http://remotesearch.blogspot.com/ Please visit these sites to get some details..

5 cord RCA ("phono") Cord lay out 3 video - RED, BLUE & GREEN and 2 Audio - LEFT and RIGHT** **RED has denoted "right"

http://www.tvrepairkits.com/xcart/ws-65315/

Kevin, I have same model ws-65315 error code 2-2

If the TV is already hdtv...no. Try reprogramming tv to find hd stations or if receiving signal from outdoor aerial make sure aerial is digital and facing right direction.

If you don't mind, you can change the TV now. You will be really happy.

Your TV MUST support 720P or higher resolution to work with an Apple TV.

I do not see any way unless you can outfit a connection to one of the rear inputs---this set was never designed for this type of use so aspect if connected would likely not be useable.

If the model number is correct the set may have in the tech menu a way to move centering etc with the original remote.I can get the information for that if needed but what is the issue? What does the picture look like after the move?

I would take a good look to make sure it got back together correctly, set does have a hidden adjustment menu once entered the Mitsubishi remote can adjust a lot of things including centering etc, want to be careful in that menu,,,confirm the model and I will give you the four digit enter code for the set.

if the reds and blues look 3d etc it is a convergence problem. see attached photos of a typical convergence problem.

Convergence, Adjustment, or OPTION menu?

there should be a menu function on the tv remote push that to bring you to options and scroll around for picture

Yes, they have other than convergence circuit problems----very few issues or troubles.You should test the shops by asking if they have the 4 digit code number for this model for the OPTION MENU---set has 3 hidden menus and OPTION menu will allow a hard reset of entire set---the other two menus are adjustment and convergence menus.If some shop has no idea what the option menu is----pass them.

ONLY 1 of 2 things can cause this problem----First thing to do is remove front speaker grill--it should pull out and issecured with plastic pegs--behind it you will find an inspection plate---Notice the one or two pairs of wires coming from the front keyboard of theset---remove the inspection plate and follow the wires to the right--you canunplug both plugs(most have two and they are marked with letters and differents so you cannot get them wrong)The idea here is to remove the front keyboard with its reset button etc fromthe circuit---You will still be able to try to turn the set on with theremote---These sets have a Receiver that is called a DM board--(large metal box to theleft as you look from the back) and if the power goes out the green light willblink for about 70 seconds and then go out---it is the Receiver booting up. Itis called the DM board.If disconnecting the keyboard allows the set to turn on--you have a bad resetswitch and two choices---either operate the set only with the remote or toremove the front screen and get at the reset switch (it is tiny) and removeand/or replace it.If disconnecting the keyboard does not restore the set to operation---thereceiver is bad---there are 4 or more caps and some pico fuses that can fail inthat unit---Mitsubishi no longer sells or repairs these--if it is bad and notthe caps there is a company you can send the unit to and have it repaired--ifyou need to know their name let me know---You can call them and get a quote for repairing the receiver.Let me know what more information you need--I am here to help.SD TECH

here it is :http://www.mitsubishi-tv.com/pdf/ownersguides/WS-55315.pdfSD TECH

Mitsubishi self check: MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.

MOSTOF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.

this model has a self check, when green light comes on and then goes off. Push and hold both the Menu and Input buttons on the front of the set for at least 5 seconds and release both.

Power light will blink a two digit error code like 2 blinks 2 blinks, a pause and then repeat it several times.

Let me know what error code you find and I will tell you what it means.


SD TECH